Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014599 AUDIO / VIDEO _0074081 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, and also the radio and display receiver assembly itself cannot function.

WIRING DIAGRAM

E229628E08
0.26,1.156 0.813,1.333 0.552,0.177 10 false Volume- 1.031,4.656 1.615,4.833 0.583,0.177 10 false Off hook 1.24,5.573 3.177,5.75 1.938,0.177 10 false Steering Pad Switch Assembly 1.802,4.656 2.375,4.833 0.573,0.177 10 false On hook 1.031,1.156 1.625,1.333 0.594,0.177 10 false Volume+ 2.958,1.156 3.167,1.333 0.208,0.177 10 false Up 5.01,0.594 5.302,0.771 0.292,0.177 10 false AU1 5,1.542 5.396,1.719 0.396,0.177 10 false EAU 5.01,2.5 5.302,2.677 0.292,0.177 10 false AU3 5.01,3.771 5.302,3.948 0.292,0.177 10 false AU2 6.281,0.677 6.656,0.854 0.375,0.177 10 false SW1 6.281,1.635 6.667,1.813 0.385,0.177 10 false SWG 6.281,2.583 6.656,2.76 0.375,0.177 10 false SW3 6.281,3.854 6.656,4.031 0.375,0.177 10 false SW2 6.208,4.302 6.583,4.479 0.375,0.177 10 false I155 1.979,1.156 2.375,1.333 0.396,0.177 10 false Down 0.5,2.104 0.792,2.281 0.292,0.177 10 false Left 1.229,2.104 1.594,2.281 0.365,0.177 10 false Right 2.823,2.104 3.177,2.281 0.354,0.177 10 false Enter 4.563,0.688 4.75,0.865 0.188,0.177 10 false z3 4.563,1.635 4.75,1.813 0.188,0.177 10 false z3 4.563,2.594 4.75,2.771 0.188,0.177 10 false z3 4.563,3.865 4.75,4.042 0.188,0.177 10 false z3 4.573,0.5 4.75,0.677 0.177,0.177 10 false 11 4.563,3.677 4.74,3.854 0.177,0.177 10 false 10 4.604,1.458 4.698,1.635 0.094,0.177 10 false 8 4.604,2.406 4.698,2.583 0.094,0.177 10 false 9 5.552,0.688 5.771,0.865 0.219,0.177 10 false I28 5.552,1.635 5.771,1.813 0.219,0.177 10 false I28 5.552,2.594 5.771,2.771 0.219,0.177 10 false I28 5.552,3.865 5.781,4.042 0.229,0.177 10 false I28 6.042,0.583 6.219,0.76 0.177,0.177 10 false 21 6.042,1.542 6.219,1.719 0.177,0.177 10 false 23 6.042,2.5 6.219,2.677 0.177,0.177 10 false 24 6.042,3.771 6.219,3.948 0.177,0.177 10 false 22 5.615,1.458 5.708,1.635 0.094,0.177 10 false 3 5.615,0.5 5.708,0.677 0.094,0.177 10 false 6 5.615,2.406 5.708,2.583 0.094,0.177 10 false 4 5.615,3.677 5.708,3.854 0.094,0.177 10 false 5 2.302,3.385 3.167,3.563 0.865,0.177 10 false MODE/HOLD 2.031,2.104 2.385,2.281 0.354,0.177 10 false Back 4.698,4.302 5.594,4.635 0.896,0.333 10 false Spiral Cable Sub-assembly 6.208,4.469 6.875,5.146 0.667,0.677 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (w/ VSC) (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC)>PRECAUTION).

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (w/o VSC) (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>PRECAUTION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
a.

Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I155-21 (SW1) - I155-23 (SWG) No switch pushed 95 to 105 kΩ
Up switch pushed Below 2.5 Ω
Down switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
I155-22 (SW2) - I155-23 (SWG) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω
I155-24 (SW3) - I155-23 (SWG) No switch pushed 95 to 105 kΩ
Enter switch pushed Below 2.5 Ω
Back switch pushed 313 to 345 Ω
Right switch pushed 950 to 1050 Ω
Left switch pushed 2955 to 3265 Ω



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Disconnect the steering pad switch assembly connector.

E225610C06
3.385,0.073 3.76,0.302 0.375,0.229 3.531,0.833 3.24,1.115 false 3.427,0.833 3.135,0.979 false 3.635,0.833 3.927,1.115 false 3.729,0.833 4.021,0.979 false 1.875,2.604 1.448,2.604 false 2.104,2.375 2.104,1.771 false 1.917,2.208 1.729,1.771 false 2.219,2.177 2.406,1.771 false 5.063,2.354 5.333,1.771 false 5.063,2.823 5.333,3.417 false 2.104,2.823 2.104,3.458 false 1.99,3.021 1.729,3.458 false 2.375,3.135 2.469,3.458 false 2.333,2.604 2.958,2.323 false 2.146,2.635 2.958,3 false 0.146,0.125 0.375,0.281 0.229,0.156 10 false *a 1.615,1.604 2.083,1.906 0.469,0.302 10 false *b 2.042,1.604 2.375,1.854 0.333,0.25 10 false *f 1.292,2.531 1.771,2.927 0.479,0.396 10 false *h 2.813,0.927 3.302,1.167 0.49,0.24 10 false EAU 2.948,1.104 3.51,1.385 0.563,0.281 10 false AU3 3.51,0.115 4.052,0.542 0.542,0.427 10 false z3 4.063,0.927 4.594,1.177 0.531,0.25 10 false AU1 3.927,1.104 4.427,1.385 0.5,0.281 10 false AU2 2.375,1.604 2.688,1.813 0.313,0.208 10 false *d 5.302,1.604 5.677,1.885 0.375,0.281 10 false *k 5.302,3.438 5.656,3.698 0.354,0.26 10 false *l 1.615,3.479 1.979,3.802 0.365,0.323 10 false *c 2.042,3.479 2.438,3.781 0.396,0.302 10 false *g 2.438,3.479 2.781,3.729 0.344,0.25 10 false *e 2.99,2.25 3.354,2.615 0.365,0.365 10 false *i 2.99,2.927 3.354,3.177 0.365,0.25 10 false *j
*a Component without harness connected
(Steering Pad Switch Assembly)
*b Volume+
*c Volume- *d Back
*e MODE/HOLD *f Up
*g Down *h Left
*i Right *j Enter
*k Off hook *l On hook



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-11 (AU1) - z3-8 (EAU) No switch pushed 95 to 105 kΩ
Up switch pushed Below 2.5 Ω
Down switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
z3-10 (AU2) - z3-8 (EAU) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω
z3-9 (AU3) - z3-8 (EAU) No switch pushed 95 to 105 kΩ
Enter switch pushed Below 2.5 Ω
Back switch pushed 313 to 345 Ω
Right switch pushed 950 to 1050 Ω
Left switch pushed 2955 to 3265 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Disconnect the steering pad switch assembly connector.


b.

Disconnect the spiral cable sub-assembly connector.


c.
E263757C14
1.323,0.583 1.625,0.813 0.302,0.229 0.458,3.833 0.76,4.063 0.302,0.229 1.656,0.969 2.021,0.74 false 2,0.969 2.135,0.75 false 2.417,0.969 2.26,0.74 false 2.75,0.979 2.365,0.74 false 0.688,4.229 1.188,3.875 false 1.115,4.229 1.292,3.875 false 1.5,4.24 1.427,3.875 false 1.865,4.229 1.51,3.865 false 0.24,0.188 0.552,0.385 0.313,0.198 10 *a 1.25,0.313 1.563,0.51 0.313,0.198 10 *b 0.365,3.573 0.677,3.771 0.313,0.198 10 *c 1.417,0.615 1.729,0.813 0.313,0.198 10 z3 0.531,3.875 0.99,4.073 0.458,0.198 10 I28 1.469,0.99 1.927,1.188 0.458,0.198 10 AU1 1.865,0.99 2.323,1.188 0.458,0.198 10 AU2 2.333,0.99 2.792,1.188 0.458,0.198 10 AU3 2.75,0.979 3.208,1.177 0.458,0.198 10 EAU 0.521,4.25 0.979,4.448 0.458,0.198 10 EAU 0.938,4.25 1.396,4.448 0.458,0.198 10 AU3 1.344,4.24 1.802,4.438 0.458,0.198 10 AU2 1.76,4.24 2.219,4.438 0.458,0.198 10 AU1
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-8 (EAU) - I28-3 (EAU) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
z3-11 (AU1) - I28-6 (AU1) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
z3-10 (AU2) - I28-5 (AU2) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
z3-9 (AU3) - I28-4 (AU3) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right



d.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-8 (EAU) - I28-3 (EAU) Always Below 3 Ω
z3-11 (AU1) - I28-6 (AU1) Always Below 3 Ω
z3-10 (AU2) - I28-5 (AU2) Always Below 3 Ω
z3-9 (AU3) - I28-4 (AU3) Always Below 3 Ω


NOTICE:
·

Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.

·

The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



HINT:



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY