Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014599 AUDIO / VIDEO _0074081 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

·

The radio and display receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the radio and display receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.


WIRING DIAGRAM

E227677E14
0.27,3.119 0.55,3.266 0.28,0.147 10 S7 0.27,3.287 2.058,3.794 1.788,0.507 10 Roof Console Box Assembly (Telephone Microphone Assembly) 5.678,3.119 6.005,3.266 0.326,0.147 10 I155 5.678,3.287 6.89,3.622 1.212,0.336 10 Radio and Display Receiver Assembly 5.758,1.162 5.862,1.309 0.104,0.147 10 5 5.928,1.255 6.312,1.402 0.384,0.147 10 MIN+ 5.758,0.686 5.862,0.833 0.104,0.147 10 4 5.928,0.778 6.36,0.925 0.432,0.147 10 MACC 5.686,1.638 5.878,1.785 0.192,0.147 10 19 5.928,1.731 6.312,1.878 0.384,0.147 10 MIN- 5.686,2.115 5.878,2.262 0.192,0.147 10 18 5.928,2.207 6.355,2.354 0.427,0.147 10 SGND 5.758,2.605 5.865,2.752 0.106,0.147 10 6 5.928,2.684 6.32,2.831 0.392,0.147 10 SNS2 1.33,2.605 1.512,2.752 0.182,0.147 10 15 1.33,0.686 1.512,0.833 0.182,0.147 10 14 1.33,1.162 1.512,1.309 0.182,0.147 10 13 1.33,1.638 1.512,1.785 0.182,0.147 10 12 0.886,2.684 1.273,2.831 0.387,0.147 10 SNS2 0.824,0.779 1.306,0.926 0.483,0.147 10 MACC 0.834,1.255 1.271,1.402 0.437,0.147 10 MCO+ 0.842,1.732 1.299,1.879 0.456,0.147 10 MCO- 2.506,2.328 3.164,2.475 0.658,0.147 10 (Shielded) 4.019,2.328 4.677,2.475 0.658,0.147 10 (Shielded)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the radio and display receiver assembly connector.


b.

Disconnect the roof console box assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I155-6 (SNS2) - S7-15 (SNS2) Always Below 1 Ω
I155-4 (MACC) - S7-14 (MACC) Always Below 1 Ω
I155-5 (MIN+) - S7-13 (MCO+) Always Below 1 Ω
I155-19 (MIN-) - S7-12 (MCO-) Always Below 1 Ω
I155-6 (SNS2) - Body ground Always 10 kΩ or higher
I155-4 (MACC) - Body ground Always 10 kΩ or higher
I155-5 (MIN+) - Body ground Always 10 kΩ or higher
I155-19 (MIN-) - Body ground Always 10 kΩ or higher
I155-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the radio and display receiver assembly connector.


b.

Reconnect the roof console box assembly (telephone microphone assembly) connector.


c.
E176671C36
1.479,0.542 1.969,0.833 0.49,0.292 2.229,2.01 2.896,2.698 false 2.229,1.74 2.854,1.302 false 2.052,2.01 1.385,2.698 false 1.604,0.604 2.219,0.927 0.615,0.323 10 false I155 0.208,0.146 0.781,0.542 0.573,0.396 10 false *a 2.75,2.719 3.427,2.99 0.677,0.271 10 false SGND 2.875,1.208 3.427,1.469 0.552,0.26 10 false MACC 1.167,2.719 1.833,3.083 0.667,0.365 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I155-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I155-18 (SGND) - Body ground Always Below 1 Ω
I155-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the roof console box assembly (telephone microphone assembly) connector.


b.
E187117C27
1.469,0.24 1.958,0.531 0.49,0.292 1.781,1.396 1.406,1.667 false 2.125,1.406 2.5,1.677 false 1.646,0.302 2.208,0.656 0.563,0.354 10 false S7 0.135,0.115 0.667,0.458 0.531,0.344 10 false *a 1.135,1.708 1.75,2 0.615,0.292 10 false SNS2 2.302,1.708 2.927,2.01 0.625,0.302 10 false MCO-
*a Component without harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S7-15 (SNS2) - S7-12 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the radio and display receiver assembly connector.


b.

Reconnect the roof console box assembly (telephone microphone assembly) connector.


c.

Turn the ignition switch to ACC.


d.
E187122C23
1.49,0.5 1.979,0.792 0.49,0.292 2.021,2.25 1.479,2.781 false 2.156,2.25 2.656,2.75 false 1.667,0.563 2.208,0.885 0.542,0.323 10 false S7 0.177,0.094 0.521,0.365 0.344,0.271 10 false *a 1.042,2.771 1.719,3.063 0.677,0.292 10 false MCO+ 2.542,2.771 3.24,3.135 0.698,0.365 10 false MCO-
*a Component with harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the roof console box assembly (telephone microphone assembly) connector.


e.

Check the waveform of the telephone microphone assembly using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output A
A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output B




A

B

5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.

Check if the same malfunction recurs.


Result:
Result Proceed to
Malfunction does not recur (returns to normal) A
Malfunction recurs B



A

END

B

REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)