Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014600 NAVIGATION / MULTI INFO DISPLAY _0074086 NAVIGATION SYSTEM(for HDD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  Microphone Circuit between Microphone and Navigation Receiver Assembly  


DESCRIPTION

·

The navigation ECU sub-assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the navigation ECU sub-assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the navigation ECU sub-assembly.


WIRING DIAGRAM

E227677E32
0.26,3.094 0.615,3.302 0.354,0.208 10 false S7 0.26,3.24 2.052,3.75 1.792,0.51 10 false Roof Console Box Assembly (Telephone Microphone Assembly) 5.771,3.115 6.094,3.26 0.323,0.146 10 false I67 5.76,1.167 5.865,1.313 0.104,0.146 10 false 5 5.927,1.25 6.313,1.396 0.385,0.146 10 false MIN+ 5.76,0.688 5.865,0.833 0.104,0.146 10 false 4 5.917,0.802 6.563,1.281 0.646,0.479 10 false MACC 5.688,1.635 5.875,1.781 0.188,0.146 10 false 19 5.927,1.729 6.313,1.875 0.385,0.146 10 false MIN- 5.688,2.115 5.875,2.26 0.188,0.146 10 false 18 5.927,2.208 6.354,2.354 0.427,0.146 10 false SGND 5.76,2.604 5.865,2.75 0.104,0.146 10 false 6 5.927,2.688 6.323,2.833 0.396,0.146 10 false SNS2 1.323,2.594 1.615,2.813 0.292,0.219 10 false 15 1.323,0.677 1.615,1.021 0.292,0.344 10 false 14 1.323,1.156 1.594,1.417 0.271,0.26 10 false 13 1.323,1.625 1.563,1.865 0.24,0.24 10 false 12 0.875,2.708 1.344,2.948 0.469,0.24 10 false SNS2 0.823,0.781 1.385,1.021 0.563,0.24 10 false MACC 0.833,1.25 1.281,1.552 0.448,0.302 10 false MCO+ 0.844,1.729 1.354,2.177 0.51,0.448 10 false MCO- 2.51,2.323 3.167,2.469 0.656,0.146 10 false (Shielded) 4.021,2.323 4.781,2.615 0.76,0.292 10 false (Shielded) 5.771,3.281 6.781,3.667 1.01,0.385 10 false Navigation ECU Sub-assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the navigation ECU sub-assembly connector.


b.

Disconnect the roof console box assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-4 (MACC) - S7-14 (MACC) Always Below 1 Ω
I67-5 (MIN+) - S7-13 (MCO+) Always Below 1 Ω
I67-19 (MIN-) - S7-12 (MCO-) Always Below 1 Ω
I67-6 (SNS2) - S7-15 (SNS2) Always Below 1 Ω
I67-4 (MACC) - Body ground Always 10 kΩ or higher
I67-5 (MIN+) - Body ground Always 10 kΩ or higher
I67-19 (MIN-) - Body ground Always 10 kΩ or higher
I67-18 (SGND) - Body ground Always 10 kΩ or higher
I67-6 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT NAVIGATION ECU SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NAVIGATION ECU SUB-ASSEMBLY
a.

Reconnect the navigation ECU sub-assembly connector.


b.

Reconnect the roof console box assembly (telephone microphone assembly) connector.


c.
E176671C39
1.479,0.542 1.969,0.833 0.49,0.292 2.229,2 2.896,2.688 false 2.198,1.74 2.865,1.281 false 2.052,2 1.385,2.688 false 1.635,0.604 2.031,0.844 0.396,0.24 10 false I67 0.208,0.146 0.438,0.302 0.229,0.156 10 false *a 2.75,2.698 3.198,2.854 0.448,0.156 10 false SGND 2.875,1.198 3.323,1.354 0.448,0.156 10 false MACC 1.167,2.698 1.51,2.854 0.344,0.156 10 false MIN-
*a Component with harness connected
(Navigation ECU Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I67-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-18 (SGND) - Body ground Always Below 1 Ω
I67-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

3.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the roof console box assembly (telephone microphone assembly) connector.


b.
E187117C31
1.458,0.26 1.885,0.542 0.427,0.281 1.76,1.396 1.406,1.688 false 2.135,1.406 2.469,1.708 false 1.604,0.313 1.885,0.49 0.281,0.177 10 false S7 0.156,0.146 0.573,0.427 0.417,0.281 10 false *a 1.219,1.74 1.635,1.938 0.417,0.198 10 false SNS2 2.344,1.74 2.771,1.938 0.427,0.198 10 false MCO-
*a Component without harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S7-15 (SNS2) - S7-12 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the navigation ECU sub-assembly connector.


b.
E187122C25
1.5,0.448 1.906,0.74 0.406,0.292 2.021,2.198 1.479,2.729 false 2.156,2.198 2.656,2.698 false 1.625,0.51 2.042,0.823 0.417,0.313 10 false S7 0.177,0.198 0.635,0.594 0.458,0.396 10 false *a 1.01,2.719 1.469,2.917 0.458,0.198 10 false MCO+ 2.542,2.719 2.969,2.917 0.427,0.198 10 false MCO-
*a Component with harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly))


Reconnect the roof console box assembly (telephone microphone assembly) connector.


c.

Turn the ignition switch to ACC.


d.

Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the roof console box assembly (telephone microphone assembly) connector.


e.

Check the waveform of the telephone microphone assembly using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output A
A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output B




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
5.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.

Check if the same malfunction recurs.


Result:
Result Proceed to
Malfunction does not recur (returns to normal) A
Malfunction recurs B



A

END

B

REPLACE ROOF CONSOLE BOX ASSEMBLY