Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014600 NAVIGATION / MULTI INFO DISPLAY _0074086 NAVIGATION SYSTEM(for HDD) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The navigation ECU sub-assembly and stereo component amplifier assembly are connected by the AVC-LAN communication line.

When an AVC-LAN communication error occurs between the navigation ECU sub-assembly and stereo component amplifier assembly, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D3 Stereo Component Amplifier Disconnected When either condition below is met:
·

Stereo component amplifier assembly is/was not connected while the ignition switch is ON or ACC.

·

Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started.


·

Stereo component amplifier assembly power source circuit

·

AVC-LAN circuit between navigation ECU sub-assembly and stereo component amplifier assembly

·

Stereo component amplifier assembly

·

Navigation ECU sub-assembly

·

Harness or connector



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

·

The navigation ECU sub-assembly is the master unit.



WIRING DIAGRAM

E226156E27
0.542,0.635 1.396,0.823 0.854,0.188 10 false from Battery 0.333,1.427 1.385,1.75 1.052,0.323 10 false from ACC NO. 1 Relay 2.76,1.677 3.458,1.865 0.698,0.188 10 false ECU-ACC 3.219,2.417 3.604,2.604 0.385,0.188 10 false TX1+ 3.25,2.802 3.604,2.99 0.354,0.188 10 false TX1- 5.604,3.219 6.073,3.406 0.469,0.188 10 false GND 5.615,2.823 6,3.01 0.385,0.188 10 false TX- 5.615,2.427 6,2.615 0.385,0.188 10 false TX+ 5.604,1.417 5.99,1.604 0.385,0.188 10 false ACC 5.594,0.646 5.979,0.833 0.385,0.188 10 false +B 5.344,2.625 5.531,2.813 0.188,0.188 10 false 7 5.344,2.219 5.438,2.406 0.094,0.188 10 false 8 5.333,0.458 5.521,0.646 0.188,0.188 10 false 1 3.646,2.323 3.74,2.51 0.094,0.188 10 false 7 3.646,2.729 3.74,2.917 0.094,0.188 10 false 8 2.615,3.344 2.958,3.531 0.344,0.188 10 false I67 5.427,3.729 6.635,4.156 1.208,0.427 10 false Stereo Component Amplifier Assembly 2.969,0.885 3.333,1.073 0.365,0.188 10 false AMP 5.344,3.021 5.438,3.208 0.094,0.188 10 false 3 5.281,3.208 5.552,3.396 0.271,0.188 10 false I68 5.281,0.646 5.552,0.833 0.271,0.188 10 false I68 5.271,1.438 5.542,1.625 0.271,0.188 10 false I69 5.271,2.427 5.542,2.615 0.271,0.188 10 false I69 5.271,2.802 5.542,2.99 0.271,0.188 10 false I69 5.292,1.24 5.479,1.427 0.188,0.188 10 false 12 2.615,3.5 3.573,3.896 0.958,0.396 10 false Navigation ECU Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DTC
a.

If DTC B15C3 is output, perform the troubleshooting of DTC B15C3 first.

Result:
Result Proceed to
DTC B15C3 is not output. A
DTC B15C3 is output. B




A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY, BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY, BODY GROUND)
a.

Disconnect the stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I68-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I68-1 (+B) - I68-3 (GND) Always 11 to 14 V
I69-12 (ACC) - I68-3 (GND) Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the navigation ECU sub-assembly connector.


b.

Disconnect the stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-7 (TX1+) - I69-8 (TX+) Always Below 1 Ω
I67-8 (TX1-) - I69-7 (TX-) Always Below 1 Ω
I67-7 (TX1+) - Body ground Always 10 kΩ or higher
I67-8 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG