Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014600 NAVIGATION / MULTI INFO DISPLAY _0074086 NAVIGATION SYSTEM(for HDD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the navigation ECU sub-assembly. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E226163E05
0.829,1.169 1.295,1.39 0.466,0.221 10 UDO- 0.969,0.576 1.222,0.797 0.253,0.221 10 UPI 0.843,2.355 1.262,2.576 0.419,0.221 10 UJSG 0.815,1.776 1.234,1.997 0.419,0.221 10 UDO+ 0.829,2.956 1.248,3.177 0.419,0.221 10 UJSS 5.985,1.169 6.451,1.39 0.466,0.221 10 US1- 5.985,0.576 6.386,0.797 0.402,0.221 10 USV1 5.985,2.355 6.404,2.576 0.419,0.221 10 UGD1 5.985,1.776 6.404,1.997 0.419,0.221 10 US1+ 5.985,2.956 6.404,3.177 0.419,0.221 10 USG1 1.328,0.476 1.461,0.697 0.133,0.221 10 1 1.328,1.081 1.461,1.302 0.133,0.221 10 2 1.328,1.674 1.461,1.895 0.133,0.221 10 3 1.328,2.258 1.461,2.479 0.133,0.221 10 4 1.328,2.86 1.461,3.081 0.133,0.221 10 5 0.152,3.391 0.446,3.553 0.294,0.163 10 I146 0.152,3.537 1.832,3.868 1.681,0.331 10 No. 1 Stereo Jack Adapter Assembly 3.262,3.096 3.95,3.332 0.688,0.237 10 (Shielded) 5.769,0.476 5.902,0.697 0.133,0.221 10 1 5.769,1.075 5.902,1.296 0.133,0.221 10 2 5.769,1.674 5.902,1.895 0.133,0.221 10 3 5.769,2.258 5.902,2.479 0.133,0.221 10 4 5.769,2.86 5.902,3.081 0.133,0.221 10 5 5.812,3.391 6.176,3.553 0.364,0.163 10 I147 5.808,3.554 6.825,3.941 1.016,0.387 10 Navigation ECU Sub-assembly

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while to begin play.

·

When using a USB device, files that are protected by copyright cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

1.

Add numbers in front of the file names.

2.

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>SYSTEM DESCRIPTION


Result:
Result Proceed to
No playable files exist, or incompatible device format or version A
Playable files exist, and compatible device format or version B




A

USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

B

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.
E226480C53
1.458,2.271 1.99,2.563 0.531,0.292 1.458,0.167 1.99,0.458 0.531,0.292 1.49,3.427 1,3.427 false 1.583,1.427 1.115,1.594 false 2.333,1.594 1.844,1.417 false 1.583,1.26 1.083,1.26 false 2.448,3.427 1.938,3.427 false 2.427,1.26 1.833,1.26 false 1.615,3.448 1,3.844 false 1.813,3.448 2.448,3.688 false 1.781,3.542 2.448,3.979 false 1.781,1.552 2.281,1.927 false 0.177,2.25 0.354,2.427 0.177,0.177 10 false *b 1.552,2.323 1.906,2.479 0.354,0.156 10 false I146 0.688,3.344 0.948,3.5 0.26,0.156 10 false UPI 0.521,3.771 0.917,3.927 0.396,0.156 10 false UDO- 0.177,0.083 0.354,0.26 0.177,0.177 10 false *a 1.563,0.229 1.917,0.385 0.354,0.156 10 false I147 0.646,1.51 1.021,1.667 0.375,0.156 10 false US1+ 2.354,1.51 2.708,1.667 0.354,0.156 10 false US1- 0.583,1.177 0.99,1.333 0.406,0.156 10 false UGD1 2.469,3.344 2.865,3.5 0.396,0.156 10 false UJSG 2.469,3.615 2.885,3.771 0.417,0.156 10 false UDO+ 2.469,3.917 2.865,4.073 0.396,0.156 10 false UJSS 2.438,1.177 2.823,1.333 0.385,0.156 10 false USV1 2.302,1.854 2.708,2.01 0.406,0.156 10 false USG1
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Disconnect the No. 1 stereo jack adapter assembly connector.


b.

Disconnect the navigation ECU sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I146-1 (UPI) - I147-1 (USV1) Always Below 1 Ω
I146-2 (UDO-) - I147-2 (US1-) Always Below 1 Ω
I146-3 (UDO+) - I147-3 (US1+) Always Below 1 Ω
I146-4 (UJSG) - I147-4 (UGD1) Always Below 1 Ω
I146-5 (UJSS) - I147-5 (USG1) Always Below 1 Ω
I146-1 (UPI) - Body ground Always 10 kΩ or higher
I146-2 (UDO-) - Body ground Always 10 kΩ or higher
I146-3 (UDO+) - Body ground Always 10 kΩ or higher
I146-4 (UJSG) - Body ground Always 10 kΩ or higher
I146-5 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION ECU SUB-ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NAVIGATION ECU SUB-ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.

Reconnect the navigation ECU sub-assembly connector.


b.
E226479C11
1.51,0.917 1.948,1.146 0.438,0.229 1.948,2.104 2.552,2.302 false 1.5,2.083 0.854,2.302 false 1.604,0.938 2.135,1.5 0.531,0.563 10 false I146 2.594,2.385 3.208,2.74 0.615,0.354 10 false UJSG 0.667,2.365 0.938,2.51 0.271,0.146 10 false UPI 0.188,0.167 0.385,0.333 0.198,0.167 10 false *a
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I146-1 (UPI) - I146-4 (UJSG) Ignition switch ACC 5 V



Result:
Proceed to
OK
NG



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that backup music data is available before performing this operation.


OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the ignition switch off.

HINT:

When this malfunction occurs, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly


HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>SYSTEM DESCRIPTION



Result:
Proceed to
NEXT



NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if a USB device or "iPod" is recognized by the navigation ECU sub-assembly, and if information such as track, artist and album names are displayed on the screen.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE