Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074094 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  OPERATION CHECK  


Blind spot monitor beam axis inspection


a.

When performing the blind spot monitor beam axis inspection, move the vehicle to a place where the space shown in the illustration can be secured.

E224418E08
0.208,0.135 0.615,0.323 0.406,0.188 12 false LH: 4.042,0.135 4.417,0.323 0.375,0.188 12 false RH: 0.156,1.448 0.438,1.646 0.281,0.198 10 false 2 m 0.99,3.979 2.052,4.25 1.063,0.271 10 false 6 m (19.69 ft.) 2.271,4 2.552,4.198 0.281,0.198 10 false 3 m 4.583,4 4.875,4.198 0.292,0.198 10 false 3 m 6.76,1.458 7.042,1.656 0.281,0.198 10 false 2 m 6.74,3.583 7.042,3.781 0.302,0.198 10 false 8 m 0.188,3.385 0.469,3.583 0.281,0.198 10 false 8 m 3.135,1.792 4,1.979 0.865,0.188 10 false Rear Bumper 1.438,0.323 2.656,0.51 1.219,0.188 10 false Left side of vehicle 4.552,0.323 5.865,0.51 1.313,0.188 10 false Right side of vehicle 1.292,4.344 2.375,4.542 1.083,0.198 10 false : Inspection Area 5.333,4.01 6.313,4.24 0.979,0.229 10 false 6 m (19.69 ft.) 4.479,4.167 5.313,4.521 0.833,0.354 10 false (9.85 ft.) 2.542,3.99 3.094,4.188 0.552,0.198 10 false (9.85 ft.) 0.031,3.781 0.719,4.021 0.688,0.24 10 false (26.25 ft.) 0,1.573 0.542,1.781 0.542,0.208 10 false (6.57 ft.) 6.542,3.802 7.135,3.979 0.594,0.177 10 false (26.25 ft.) 6.625,1.625 7.156,1.896 0.531,0.271 10 false (6.57 ft.)

NOTICE:
·

Perform this inspection on level ground.

·

Make sure that there are no metal objects around the vehicle or on the ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.

·

Do not place an object other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 9 m (29.53 ft.) x L 10 m (32.81 ft.) x H 4 m (13.13 ft.)) shown in the illustration.

·

Check that DTC C1ABB and DTC C1ABC are not output.




b.

Procedure to enter the Test Mode

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the blind spot monitor main switch (warning canceling switch assembly) on.


iv.

Turn the intelligent tester on.


v.

Switch the blind monitor sensor to Test Mode using the intelligent tester. Enter the following menus: Body / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Beam Axis Inspection or BSM Slave Beam Axis Inspection.

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Inspection
50005 313 4202
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Inspection
50005 314 4203


c.
E224411E01
0.122,0.094 2.187,0.266 2.066,0.173 10 Blind spot monitor indicator 0.539,0.994 0.799,1.167 0.26,0.173 10 LH: 0.539,2.803 0.799,2.975 0.26,0.173 10 RH:

Perform the blind spot monitor beam axis inspection.

i.

Check that the outer rear view mirror indicators are not illuminated.

NOTICE:

If an indicator is illuminated, because there is a possibility that the sensors are reacting to metal or other items, move the vehicle to another place.



ii.

Place the reflector at position A.

SST
09870-60000  (09870-60010)
09870-60040  

HINT:

Set the reflector so that its center is 450 mm (1.48 ft.) above the floor.



iii.

Enter Test Mode using the intelligent tester. Move the reflector from position A to B as shown in the illustration.

E224419E03
0.906,1.125 1.375,1.76 false 0.948,3.25 1.542,2.708 false 6.271,1.125 5.719,1.781 false 6.125,3.26 5.635,2.729 false 0.198,0.052 0.531,0.281 0.333,0.229 12 false LH: 3.792,0.052 4.125,0.281 0.333,0.229 12 false RH: 1.646,0.135 2.844,0.302 1.198,0.167 10 false Left side of vehicle 4.302,0.135 5.615,0.302 1.313,0.167 10 false Right side of vehicle 0.49,0.906 1.375,1.083 0.885,0.177 10 false Warning area 5.896,0.906 6.781,1.083 0.885,0.177 10 false Warning area 3.146,1.688 4.021,1.854 0.875,0.167 10 false Rear bumper 4.125,2.156 4.375,2.344 0.25,0.188 10 false 3 m 3.156,2.167 3.427,2.354 0.271,0.188 10 false 3 m 3.021,2.76 3.177,2.948 0.156,0.188 10 false A 4.052,2.76 4.177,2.948 0.125,0.188 10 false A 2.354,2.76 2.51,2.948 0.156,0.188 10 false B 4.729,2.76 4.854,2.948 0.125,0.188 10 false B 1.615,2.76 1.771,2.948 0.156,0.188 10 false C 5.438,2.76 5.594,2.948 0.156,0.188 10 false C 1.646,3.302 2.031,3.458 0.385,0.156 10 false 1.5 m 5.208,3.302 5.625,3.458 0.417,0.156 10 false 1.5 m 2.083,3.302 2.396,3.458 0.313,0.156 10 false 1 m 4.583,3.135 4.875,3.313 0.292,0.177 10 false 1 m 2.427,3.51 2.698,3.667 0.271,0.156 10 false 3 m 4.573,3.49 4.844,3.646 0.271,0.156 10 false 3 m 0.656,3.281 1.25,3.448 0.594,0.167 10 false Reflector 5.896,3.281 6.49,3.448 0.594,0.167 10 false Reflector 2.292,3.646 2.885,3.802 0.594,0.156 10 false (9.85 ft.) 1.5,3.458 2.094,3.698 0.594,0.24 10 false (4.93 ft.) 2.354,3.313 2.896,3.479 0.542,0.167 10 false (3.29 ft.) 4.458,3.625 5.052,3.781 0.594,0.156 10 false (9.85 ft.) 5.156,3.448 5.844,3.719 0.688,0.271 10 false (4.93 ft.) 4.479,3.302 5.021,3.469 0.542,0.167 10 false (3.29 ft.) 3.115,2.323 3.792,2.635 0.677,0.313 10 false (9.85 ft.) 4.083,2.313 4.844,2.563 0.76,0.25 10 false (9.85 ft.)

HINT:
·

Make sure that the orientation of the reflector is as shown in the illustration.

·

The acceptable range for sensor installation angle (horizontal direction) that allows the blind spot monitor system to operate correctly is as shown by the shaded areas inside the broken lines in the illustration (the warning areas).



NOTICE:

While moving the reflector, make sure that no one or no objects pass between the vehicle and the reflector.



iv.

After placing the reflector in the specified position, quickly exit the inspection area and make sure that objects other than the reflector are not in the inspection area and check that the blind spot monitor indicator does not illuminate.

HINT:

If the indicator illuminates, repeat the same action (i.e. move the reflector from A to B). If the indicator illuminates again, check the blind spot monitor sensor installation condition.



v.

Move the reflector from position B to C as shown in the illustration.

HINT:

Make sure that the orientation of the reflector is as shown in the illustration.


NOTICE:

While moving the reflector, make sure that no one or no objects pass between the vehicle and the reflector.



vi.

After placing the reflector in the specified position, quickly exit the inspection area and make sure that objects other than the reflector are not in the inspection area and check that the blind spot monitor indicator illuminates.

HINT:

If the indicator does not illuminate, repeat the same action (i.e. move the reflector from B to C). If the indicator does not illuminate again, check the blind spot monitor sensor installation condition.



vii.

Finish Test Mode.




The Blind Spot Monitor Installation Condition Inspection


NOTICE:
·

Perform this inspection on level ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.



a.

b.

Attach a jig similar to the one shown in the illustration to the outward facing surface of the blind spot monitor sensor and check that the blind spot monitor sensor is perpendicular to the floor surface or within the allowable range.

E233717E01
5.912,3.961 5.912,3.413 false 6.081,3.343 6.913,3.527 0.832,0.184 10 Floor surface 5.912,3.413 6.059,3.413 false 1.953,3.588 1.953,2.446 false 1.189,3.588 2.903,3.753 1.714,0.166 10 Blind Spot Monitor Sensor 3.125,3.441 4.816,3.645 1.691,0.205 10 Outward facing surface 2.298,2.115 2.983,3.504 false 0.161,0.064 1.797,0.248 1.635,0.184 10 Rear view of vehicle (RH): 5.056,1.213 5.582,0.619 false 5.582,0.619 5.729,0.619 false 5.764,0.556 6.208,0.793 0.444,0.236 10 Jig 4.611,3.251 4.874,3.251 false 4.909,3.19 5.483,3.426 0.574,0.236 10 Weight 2.983,3.504 3.095,3.504 false

E233716E10
1.677,0.885 3.042,1.417 1.365,0.531 10 false Hold this side against the blind spot monitor sensor RH. 3.26,1.76 3.542,1.969 0.281,0.208 10 false Top 5.333,3.146 5.906,3.333 0.573,0.188 10 false 100 mm 2.76,4.083 2.948,4.271 0.188,0.188 10 false A 3.979,4.083 4.167,4.271 0.188,0.188 10 false B 1.354,2.823 2.844,3.167 1.49,0.344 10 false Position where string is to be secured 1.042,6.177 2.51,6.604 1.469,0.427 10 false : Allowable range 0.219,0.188 0.833,0.427 0.615,0.24 12 false Jig: 1.552,4.979 1.74,5.167 0.188,0.188 10 false + 5.167,4.979 5.354,5.167 0.188,0.188 10 false - 5.354,3.292 6,3.479 0.646,0.188 10 false (3.94 in.) 4.156,0.896 5.531,1.5 1.375,0.604 10 false Hold this side against the blind spot monitor sensor LH.

Standard
A B
Blind spot monitor sensor RH 17mm
(0.66 in.)
-17mm
(-0.66 in.)
Blind spot monitor sensor LH 8mm
(0.31 in.)
-26mm
(1.02 in.)

NOTICE:

Allowable ranges A and B are different between the blind spot monitor sensor LH and RH.



c.
E224437E12
1.24,3.615 1.469,4.01 false 2.521,0.635 2.906,1.177 false 0.781,3.573 0.729,3.854 false 0.552,3.833 0.271,3.906 false 0.271,3.906 0.271,4.281 false 1.385,2 1.594,1.625 false 1.594,1.625 1.667,1.625 false 1.469,4.01 1.563,4.01 false 0.094,0.073 1.448,0.281 1.354,0.208 12 false Vehicle rear (LH): 1.344,0.51 2.51,0.823 1.167,0.313 10 false Vehicle center line 1.594,3.948 2.219,4.115 0.625,0.167 10 false Stud bolt 1.333,0.885 2.125,1.052 0.792,0.167 10 false Vehicle front 0.688,3.823 0.813,3.99 0.125,0.167 10 false y 1.938,3.719 2.698,3.885 0.76,0.167 10 false Vehicle rear 0.052,4.281 2.427,4.448 2.375,0.167 10 false Line parallel to the vehicle center line 1.656,2.385 2.344,2.573 0.688,0.188 10 false 135.5 mm 1.667,1.531 2.688,1.854 1.021,0.323 10 false Stud bolt center line 1.688,2.594 2.375,2.781 0.688,0.188 10 false (5.33 in.)

Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.

Standard:
Dimension Specified Value
y 26 to 66 mm
(1.03 to 2.59 in.)