Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074094 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB1  Short to +B in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a +B short in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB1 Short to +B in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

Blind spot monitor main switch (warning canceling switch assembly) is on.


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time.


·

Outer rear view mirror LH

·

Outer rear view mirror assembly LH

·

Wire harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control computer assembly LH



WIRING DIAGRAM

E233743E02
1.577,1.272 1.715,1.424 0.138,0.152 10 1 2.974,1.16 3.111,1.312 0.138,0.152 10 7 5.818,1.258 5.946,1.41 0.128,0.152 10 6 3.282,1.37 3.689,1.522 0.406,0.152 10 BDIL 5.99,1.356 6.397,1.508 0.406,0.152 10 OMIL 3.282,1.833 3.65,1.984 0.368,0.152 10 HTR- 0.218,2.155 0.597,2.307 0.378,0.152 10 IND2 5.881,3.391 6.324,3.542 0.443,0.152 10 T16 1.39,1.366 1.528,1.517 0.138,0.152 10 + 1.39,1.84 1.528,1.991 0.138,0.152 10 - 1.587,1.737 1.724,1.889 0.138,0.152 10 2 2.932,1.625 3.125,1.777 0.193,0.152 10 12 0.218,2.328 2.358,2.491 2.14,0.163 10 Outer Rear View Mirror LH 0.167,3.407 2.545,3.581 2.378,0.175 10 Outer Rear View Mirror Assembly LH 5.881,3.573 7.079,3.889 1.198,0.316 10 Blind Spot Monitor Sensor LH 0.202,2.615 2.282,2.931 2.08,0.316 10 (Outer Rear View Mirror Indicator LH) 2.932,1.356 3.16,1.508 0.228,0.152 10 z6 2.932,1.821 3.125,1.973 0.193,0.152 10 z6 3.179,3.393 4.752,3.762 1.573,0.369 10 Outer Mirror Control Computer Assembly LH 4.011,1.356 4.417,1.508 0.406,0.152 10 BDSR 4.078,1.819 4.445,1.97 0.368,0.152 10 GND 4.59,1.146 4.773,1.298 0.183,0.152 10 10 4.641,1.625 4.779,1.777 0.138,0.152 10 7 4.543,1.356 4.819,1.508 0.277,0.152 10 K12 4.543,1.821 4.875,1.973 0.332,0.152 10 K12

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)
2.INSPECT OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)
a.

Disconnect connector T16 from the blind spot monitor sensor LH.


b.
C240531C14
0.417,1.604 0.938,1.917 0.521,0.313 1.688,1.927 1.688,2.521 1.688,2.521 1.5,2.521 false 0.125,0.063 0.417,0.375 0.292,0.313 10 false *a 1.01,2.438 1.646,2.719 0.635,0.281 10 false OMIL 0.583,1.677 1.083,1.979 0.5,0.302 10 false T16
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T16-6 (OMIL) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - BLIND SPOT MONITOR SENSOR LH)
3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect connector IND2 from the outer rear view mirror LH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T16-6 (OMIL) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

NG

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH)
4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect connector z6 from the outer mirror control computer assembly LH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T16-6 (OMIL) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL COMPUTER ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH)
5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL COMPUTER ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect connector K12 from the outer mirror control computer assembly LH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T16-6 (OMIL) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL COMPUTER ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR