Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074094 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB3  Short to GND in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a ground short in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB3 Short to GND in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

Blind spot monitor main switch (warning canceling switch assembly) is on.


·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time.


·

Outer rear view mirror LH

·

Outer rear view mirror assembly LH

·

Wire harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control computer assembly LH



WIRING DIAGRAM

E233743E02
1.577,1.272 1.715,1.424 0.138,0.152 10 1 2.974,1.16 3.111,1.312 0.138,0.152 10 7 5.818,1.258 5.946,1.41 0.128,0.152 10 6 3.282,1.37 3.689,1.522 0.406,0.152 10 BDIL 5.99,1.356 6.397,1.508 0.406,0.152 10 OMIL 3.282,1.833 3.65,1.984 0.368,0.152 10 HTR- 0.218,2.155 0.597,2.307 0.378,0.152 10 IND2 5.881,3.391 6.324,3.542 0.443,0.152 10 T16 1.39,1.366 1.528,1.517 0.138,0.152 10 + 1.39,1.84 1.528,1.991 0.138,0.152 10 - 1.587,1.737 1.724,1.889 0.138,0.152 10 2 2.932,1.625 3.125,1.777 0.193,0.152 10 12 0.218,2.328 2.358,2.491 2.14,0.163 10 Outer Rear View Mirror LH 0.167,3.407 2.545,3.581 2.378,0.175 10 Outer Rear View Mirror Assembly LH 5.881,3.573 7.079,3.889 1.198,0.316 10 Blind Spot Monitor Sensor LH 0.202,2.615 2.282,2.931 2.08,0.316 10 (Outer Rear View Mirror Indicator LH) 2.932,1.356 3.16,1.508 0.228,0.152 10 z6 2.932,1.821 3.125,1.973 0.193,0.152 10 z6 3.179,3.393 4.752,3.762 1.573,0.369 10 Outer Mirror Control Computer Assembly LH 4.011,1.356 4.417,1.508 0.406,0.152 10 BDSR 4.078,1.819 4.445,1.97 0.368,0.152 10 GND 4.59,1.146 4.773,1.298 0.183,0.152 10 10 4.641,1.625 4.779,1.777 0.138,0.152 10 7 4.543,1.356 4.819,1.508 0.277,0.152 10 K12 4.543,1.821 4.875,1.973 0.332,0.152 10 K12

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL COMPUTER ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH)
2.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL COMPUTER ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect connector T16 from the blind spot monitor sensor LH.


b.

Disconnect connector K12 from the outer mirror control computer assembly LH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K12-10 (BDSR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)
a.

Disconnect connector IND2 from the outer rear view mirror LH.


b.
E233737C08
1.583,1.313 1.583,0.719 false 1.583,0.719 1.833,0.719 false 1.74,1.354 1.74,1.771 false 1.74,1.771 1.938,1.771 false 0.083,0.052 0.458,0.333 0.375,0.281 10 false *a 1.875,0.635 2.146,0.823 0.271,0.188 10 false + 2.01,1.688 2.281,1.875 0.271,0.188 10 false -
*a Component without harness connected
(Outer Rear View Mirror LH)


Check that the outer rear view mirror indicator turns on.

NOTICE:

Do not apply a voltage of more than 6 V.


i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.

Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:
Connection Specified Condition
6 V battery positive (+) → Terminal 1 (+)
6 V battery negative (-) → Terminal 2 (-)
Indicator turns on




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)

NG

REPLACE OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect connector z6 from the outer mirror control computer assembly LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z6-7 (BDIL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT OUTER MIRROR CONTROL COMPUTER ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

5.INSPECT OUTER MIRROR CONTROL COMPUTER ASSEMBLY LH
a.

Disconnect connector K12 from the outer mirror control computer assembly LH.


b.
E233744C22
2.219,0.208 2.646,0.469 0.427,0.26 2.563,1.208 2.771,1.656 false 2.323,0.26 2.76,0.521 0.438,0.26 10 false K12 2.604,1.656 3.26,2 0.656,0.344 10 false BDSR 0.219,0.125 0.563,0.417 0.344,0.292 10 false *a
*a Component without harness connected
(Outer Mirror Control Computer Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K12-10 (BDSR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE OUTER MIRROR CONTROL COMPUTER ASSEMBLY LH