Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074094 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB4  Open in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects an open in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB4 Open in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

Blind spot monitor main switch (warning canceling switch assembly) is on.


·

The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator.


·

Outer rear view mirror RH

·

Outer rear view mirror assembly RH

·

Wire harness or connector

·

Blind spot monitor sensor RH

·

Outer mirror control computer assembly RH



WIRING DIAGRAM

E233743E01
1.577,1.272 1.715,1.424 0.138,0.152 10 1 2.974,1.16 3.111,1.312 0.138,0.152 10 7 5.818,1.258 5.946,1.41 0.128,0.152 10 6 3.282,1.37 3.689,1.522 0.406,0.152 10 BDIR 5.99,1.356 6.397,1.508 0.406,0.152 10 OMIR 3.282,1.833 3.65,1.984 0.368,0.152 10 HTR- 0.218,2.155 0.597,2.307 0.378,0.152 10 IND1 5.881,3.391 6.324,3.542 0.443,0.152 10 O28 1.39,1.366 1.528,1.517 0.138,0.152 10 + 1.39,1.84 1.611,1.991 0.221,0.152 10 - 1.587,1.737 1.724,1.889 0.138,0.152 10 2 2.932,1.625 3.125,1.777 0.193,0.152 10 12 0.218,2.328 2.358,2.491 2.14,0.163 10 Outer Rear View Mirror RH 0.167,3.407 2.545,3.581 2.378,0.175 10 Outer Rear View Mirror Assembly RH 5.881,3.573 7.079,3.889 1.198,0.316 10 Blind Spot Monitor Sensor RH 0.202,2.615 2.282,2.931 2.08,0.316 10 (Outer Rear View Mirror Indicator RH) 2.932,1.356 3.16,1.508 0.228,0.152 10 z7 2.932,1.821 3.125,1.973 0.193,0.152 10 z7 3.179,3.393 4.71,3.762 1.531,0.369 10 Outer Mirror Control Computer Assembly RH 4.011,1.356 4.417,1.508 0.406,0.152 10 BDSR 4.078,1.819 4.445,1.97 0.368,0.152 10 GND 4.59,1.146 4.773,1.298 0.183,0.152 10 10 4.641,1.625 4.779,1.777 0.138,0.152 10 7 4.557,1.342 4.813,1.494 0.256,0.152 10 J13 4.557,1.821 4.889,1.973 0.332,0.152 10 J13

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL COMPUTER ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH)
2.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL COMPUTER ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect connector O28 from the blind spot monitor sensor RH.


b.

Disconnect connector J13 from the outer mirror control computer assembly RH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O28-6 (OMIR) - J13-10 (BDSR) Always Below 1 Ω
J13-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)
a.

Disconnect connector z7 from the outer mirror control computer assembly RH.


b.
E233729C01
0.292,1.052 0.771,1.344 0.479,0.292 2.094,1.24 2.823,0.458 false 1.646,1.521 2.573,1.969 false 0.167,0.063 0.552,0.375 0.385,0.313 10 false *a 0.167,2.302 0.469,2.531 0.302,0.229 10 false *1 0.448,1.125 0.781,1.354 0.333,0.229 10 false z7 2.896,0.323 3.375,0.625 0.479,0.302 10 false BDIR 2.635,1.896 3.177,2.156 0.542,0.26 10 false HTR-
*1 Outer Rear View Mirror Indicator RH
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check that the outer rear view mirror indicator turns on.

NOTICE:

Do not apply a voltage of more than 6 V.


i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.

Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:
Connection Specified Condition
6 V battery positive (+) → z7-7 (BDIR)
6 V battery negative (-) → z7-12 (HTR-)
Indicator turns on




Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR CONTROL COMPUTER ASSEMBLY RH

NG

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - OUTER MIRROR CONTROL COMPUTER ASSEMBLY RH)
4.INSPECT OUTER MIRROR CONTROL COMPUTER ASSEMBLY RH
a.

Disconnect connector J13 from the outer mirror control computer assembly RH.


b.
E233744C23
2.219,0.208 2.646,0.469 0.427,0.26 0.844,0.208 1.271,0.469 0.427,0.26 2.563,1.208 2.771,1.656 false 2.01,1.083 2.208,1.656 false 1.177,1.229 1.375,1.667 false 0.74,1.094 0.615,1.635 false 2.333,0.26 2.781,0.542 0.448,0.281 10 false J13 2.604,1.677 3.188,1.917 0.583,0.24 10 false BDSR 0.115,0.135 0.448,0.438 0.333,0.302 10 false *a 1,0.25 1.385,0.51 0.385,0.26 10 false z7 2.01,1.667 2.406,1.865 0.396,0.198 10 false GND 1.198,1.698 1.677,1.896 0.479,0.198 10 false HTR- 0.396,1.698 0.792,1.896 0.396,0.198 10 false BDIR
*a Component without harness connected
(Outer Mirror Control Computer Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J13-10 (BDSR) - z7-7 (BDIR) Always Below 1 Ω
J13-7 (GND) - z7-12 (HTR-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE OUTER MIRROR CONTROL COMPUTER ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - OUTER MIRROR CONTROL COMPUTER ASSEMBLY RH)
a.

Disconnect connector IND1 from the outer rear view mirror RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z7-7 (BDIR) - IND1-1 (+) Always Below 1 Ω
z7-12 (HTR-) - IND1-2 (-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH