Home › Power Source / Network › 2AR-FE BATTERY / CHARGING › GENERATOR › 2011.10–2015.04
RM19V0EQ _57 Power Source / Network _014602 2AR-FE BATTERY / CHARGING _0074099 GENERATOR A

2AR-FE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A194719

Using a screwdriver, puncture the center of the generator pulley cap and pry it off.

NOTICE:

Do not reuse the generator pulley cap.



Hide 27415 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.
A197237C02
0.906,1.521 1.271,1.667 1.271,1.667 1.365,1.656 true 1.677,1.052 1.76,1.427 1.76,1.427 1.854,1.427 false 1.385,1.563 1.552,1.76 0.167,0.198 10 *2 1.896,1.344 2.083,1.542 0.188,0.198 10 *1
*1 SST (A)
*2 SST (B)


Mount the generator in a vise.


b.

Install SST (A) and (B) to the pulley as shown in the illustration.

SST
09820-63021  


c.
A197239C02
2.229,0.813 2.719,0.813 false 1.938,0.563 2.104,0.25 2.104,0.25 2.188,0.25 false 2.198,0.167 2.406,0.365 0.208,0.198 10 *2 2.75,0.74 2.927,0.938 0.177,0.198 10 *1
*1 SST (A)
*2 SST (B)


Use a wrench to hold SST (A), and turn SST (B) counterclockwise to loosen the generator pulley.

NOTICE:
·

Check that the drive end frame is secured in the vise tightly.

·

Hold SST (A) tightly during the operation.




d.

Remove the generator pulley.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.

Place the generator on the generator pulley.


b.
A192779

Remove the 3 nuts and generator rear end cover.


c.
A192780

Remove the terminal insulator.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A192781

Remove the 2 screws and generator brush holder.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A192782

Remove the 4 bolts.


b.
A192783N02
1.573,0.771 1.021,0.396 1.021,0.396 0.896,0.396 false 0.531,0.323 0.833,0.5 0.302,0.177 10 false SST

Using SST, remove the generator coil.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010)


Hide 27330 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A297781

Remove the generator washer.


b.
A297782

Remove the generator rotor assembly.


Hide 27310B 7.INSPECT GENERATOR DRIVE END FRAME BEARING

Hide 27310B 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A192787

Remove the 4 screws and bearing retainer.


b.
A192788N02
1.542,1.323 0.885,1.323 0.885,1.323 0.885,1.156 false 1.563,1.156 0.479,1.156 false 0.198,1.083 0.51,1.271 0.313,0.188 10 SST

Using SST and a hammer, tap out the bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)