Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0200  Lost Communication with "Door Control Module B"  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0200 Lost Communication with "Door Control Module B" No communication from the outer mirror control ECU assembly continues.
·

Outer mirror control ECU assembly (for front passenger side) branch line or connector

·

Power source circuit of outer mirror control ECU assembly (for front passenger side)

·

Outer mirror control ECU assembly (for front passenger side) ground circuit

·

Outer mirror control ECU assembly (for front passenger side)


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.

HINT:

This diagnosis procedure is for when DTC U0200 is output by the main body ECU (multiplex network body ECU) (Intelligent tester display: Main Body).


WIRING DIAGRAM

C248163E08
2.75,0.75 3.083,0.417 3.083,0.417 3.281,0.417 false 0.708,1.667 1.104,1.813 0.396,0.146 10 false 120 Ω 0.292,2.302 0.563,2.448 0.271,0.146 10 false I12 6.156,1.667 6.552,1.813 0.396,0.146 10 false 120 Ω 0.552,2.302 1.708,2.927 1.156,0.625 10 false Main Body ECU (Multiplex Network Body ECU) 3.594,2.74 4.052,2.885 0.458,0.146 10 false CANP 3.198,3.698 5.385,4.083 2.188,0.385 10 false Outer Mirror Control ECU Assembly (for Front Passenger Side) 3.573,4.49 4.479,4.677 0.906,0.188 10 false Trouble Area 3.417,2.938 3.885,3.083 0.469,0.146 10 false CPUB 3.417,3.354 3.885,3.5 0.469,0.146 10 false SIG 3.219,2.833 3.344,2.979 0.125,0.146 10 false 6 3.74,2.542 3.854,2.688 0.115,0.146 10 false 9 4.344,2.542 4.469,2.688 0.125,0.146 10 false 8 4.844,2.979 4.969,3.125 0.125,0.146 10 false 7 4.427,3.073 4.781,3.219 0.354,0.146 10 false GND 4.146,2.74 4.604,2.885 0.458,0.146 10 false CANN 1.427,5 3.365,5.177 1.938,0.177 10 false : CAN Main Bus Line (CANH) 1.427,5.406 3.365,5.583 1.938,0.177 10 false : CAN Main Bus Line (CANL) 4.427,5 6.156,5.177 1.729,0.177 10 false : CAN Branch Line (CANH) 4.427,5.406 6.125,5.583 1.698,0.177 10 false : CAN Branch Line (CANL) 5.677,2.281 6.969,2.615 1.292,0.333 10 false CAN No. 4 Junction Connector 3.344,0.344 5.5,0.563 2.156,0.219 10 false CAN No. 3 Junction Connector 2.115,3.063 3,3.24 0.885,0.177 10 false ECU-B NO. 1 2.115,3.479 3.115,3.656 1,0.177 10 false ECU-IG1 NO. 2 3.219,3.25 3.375,3.427 0.156,0.177 10 false 5 2.885,3.698 3.167,3.844 0.281,0.146 10 false K12 0.167,0.073 1.813,0.313 1.646,0.24 12 false Sub Bus 1 (for RHD):

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 10 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

HINT:

If DTC U1002 is output from Main Body of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in the sub bus 1.


Result:
Result Proceed to
U1002 is not output from main body ECU (multiplex network body ECU) (Intelligent tester display: Main Body) A
U1002 is output from main body ECU (multiplex network body ECU) (Intelligent tester display: Main Body) B



A

2.CHECK FOR OPEN IN SUB BUS 1 LINES (OUTER MIRROR CONTROL ECU ASSEMBLY (FOR FRONT PASSENGER SIDE) BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 1 LINES (OUTER MIRROR CONTROL ECU ASSEMBLY (FOR FRONT PASSENGER SIDE) BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the outer mirror control ECU assembly (for front passenger side) connector.


c.
C204179C32
1.458,0.177 1.875,0.448 0.417,0.271 0.969,1.781 1.104,1.781 1.104,1.781 1.208,1.427 false 1.594,1.833 1.458,1.833 1.458,1.833 1.375,1.438 false 0.063,0.021 0.219,0.198 0.156,0.177 10 false *a 1.552,0.24 1.823,0.417 0.271,0.177 10 false K12 1.656,1.76 2.063,1.938 0.406,0.177 10 false CANP 0.531,1.698 0.938,1.875 0.406,0.177 10 false CANN
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K12-9 (CANP) - K12-8 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY (FOR FRONT PASSENGER SIDE))

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C204179C33
1.5,0.188 1.854,0.458 0.354,0.271 2.177,1.146 2.49,1.146 false 0.042,0.052 0.354,0.25 0.313,0.198 10 false *a 1.563,0.24 2.021,0.438 0.458,0.198 10 false K12 2.531,1.073 2.99,1.271 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K12-7 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C204179C34
1.49,0.177 1.875,0.438 0.385,0.26 0.854,0.552 1.625,0.552 1.625,0.552 1.802,1.125 false 2.417,0.552 2.167,0.552 2.167,0.552 1.948,1.135 false 0.042,0.052 0.354,0.25 0.313,0.198 10 false *a 1.563,0.229 2.021,0.427 0.458,0.198 10 false K12 0.573,0.479 1.031,0.677 0.458,0.198 10 false SIG 2.458,0.479 3.073,0.677 0.615,0.198 10 false CPUB
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K12-6 (CPUB) - Body ground Ignition switch off 11 to 14 V
K12-5 (SIG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FOR FRONT PASSENGER SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)