The main body ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 1.
When the main body ECU receives a response signal from the ECUs connected to sub bus 1, the main body ECU recognizes and memorizes that the ECU is connected to sub bus 1. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to sub bus 1 when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 1, the main body ECU determines that a malfunction exists.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| U1002 | Lost Communication with Gateway Module (Main Body ECU) | Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 1. | ·
Open or short in Sub bus 1 main line or connector ·
Open or short in Sub bus 1 branch line or connector ·
Main body ECU (Multiplex network body ECU) ·
Outer mirror control ECU assembly (for Driver side) ·
Outer mirror control ECU assembly (for Front passenger side) ·
Position control ECU and switch assembly (for Driver side) ·
Open or short in CAN No. 3 junction connector ·
Open or short in CAN No. 4 junction connector |
The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1. |
This diagnosis procedure is for when DTC U1002 is output by the main body ECU (Intelligent tester display: Main Body).
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait at least 10 seconds.
After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
Disconnect the cable from the negative (-) battery terminal.
| *1 | DLC3 |
| *a | Component with harness connected
(CAN No. 3 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| I162-1 (CANH) - I162-2 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or higher: Open circuit in a main bus line | |||
| I162-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I162-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I162-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I162-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| Open circuit in CAN main bus line | B |
| Short circuit between bus lines | C |
·
Ground short ·
+B short |
D |
A
B
C
D
Reconnect the cable to the negative (-) battery terminal.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON and recheck for DTCs.
| Result | Proceed to |
|---|---|
| U1002 is output from main body ECU (multiplex network body ECU) (Intelligent tester display: Main Body) | A |
| Other DTC is output | B |
A
B
Disconnect the wire harness connector (I162) from the CAN No. 3 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 3 Junction Connector) |
| *b | to Main Body ECU (Multiplex Network Body ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I162-1 (CANH) - I162-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the wire harness connector (I162) to the CAN No. 3 junction connector.
Disconnect the wire harness connector (I166) from the CAN No. 3 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 3 Junction Connector) |
| *b | to CAN No. 4 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I166-1 (CANH) - I166-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the wire harness connector (I166) to the CAN No. 3 junction connector.
Disconnect the wire harness connector (I167) from the CAN No. 4 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 4 Junction Connector) |
| *b | to CAN No. 3 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I167-1 (CANH) - I167-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the wire harness connector (I162) to the CAN No. 3 junction connector.
Disconnect the main body ECU (multiplex network body ECU) connector.
| *a | Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I12-9 (CANP) - I12-10 (CANN) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the wire harness connector (I162) from the CAN No. 3 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 3 Junction Connector) |
| *b | to Main Body ECU (Multiplex Network Body ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I162-1 (CANH) - I162-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the wire harness connector (I162) to the CAN No. 3 junction connector.
| *a | Component with harness connected
(CAN No. 3 Junction Connector) |
Connect the probes of an ohmmeter to terminals 1 (CANH) and 2 (CANL) of the main body ECU main line harness connector.
While observing the resistance value shown on the tester, disconnect connectors (I163, I164 and I165) from the CAN No. 3 junction connector or CAN No. 4 junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).
| *1 | Main Body ECU (Multiplex Network Body ECU) | *2 | Outer Mirror Control ECU Assembly (for Front Passenger Side) |
| *3 | CAN No. 3 Junction Connector | *4 | Outer Mirror Control ECU Assembly (for Driver Side) |
| *5 | Position Control ECU and Switch Assembly (for Driver Side) | *6 | CAN No. 4 Junction Connector |
| *1 | CAN No. 3 Junction Connector | - | - |
| *a | Junction Connector A Side | *b | Junction Connector B Side |
| *c | Earth Terminal | *d | Front view of wire harness connector
(to CAN No. 3 Junction Connector) |
| CAN No. 3 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
|---|---|---|---|
| Main body ECU (Multiplex network body ECU) | I162 | R | GR |
| Outer mirror control ECU assembly (for Front passenger side) | I163 | G | GR |
| CAN main bus line (bus line connecting CAN No. 3 junction connector and CAN No. 4 junction connector) | I166 | Y | R |
| *1 | CAN No. 4 Junction Connector | - | - |
| *a | Junction Connector A Side | *b | Junction Connector B Side |
| *c | Earth Terminal | *d | Front view of wire harness connector
(to CAN No. 4 Junction Connector) |
| CAN No. 4 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
|---|---|---|---|
| CAN main bus line (bus line connecting CAN No. 3 junction connector and CAN No. 4 junction connector) | I167 | Y | R |
| Position control ECU and switch assembly (for Driver side) | I165 | BE | GR |
| Outer mirror control ECU assembly (for Driver side) | I164 | P | GR |
Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.
| Symptom | Proceed to |
|---|---|
| The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of branch lines.) | A |
| The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.) | B |
When there is a short in one or more of the branch lines:
Reconnect all of the connectors to the CAN J/C, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
A
B
Disconnect the wire harness connector (I166) from the CAN No. 3 junction connector.
| *a | Component with harness connected
(CAN No. 3 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I162-1 (CANH) - I162-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the wire harness connector (I166) to the CAN No. 3 junction connector.
Disconnect the wire harness connector (I167) from the CAN No. 4 junction connector.
| *a | Component with harness connected
(CAN No. 3 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I162-1 (CANH) - I162-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the connector for the short-circuited branch line to the CAN junction connector (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).
Disconnect the connector that includes terminals CANH and CANL from the ECU to which the short-circuited branch line is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *a | Component with harness connected
(CAN No. 3 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I162-1 (CANH) - I162-2 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU, there may be a short in the ECU.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the wire harness connector (I162) to the CAN No. 3 junction connector.
Disconnect the main body ECU (multiplex network body ECU) connector.
| *a | Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I12-9 (CANP) - I12-10 (CANN) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the wire harness connector (I162) from the CAN No. 3 junction connector.
| *1 | DLC3 |
| *a | Rear view of wire harness connector
(to CAN No. 3 Junction Connector) |
| *b | to Main Body ECU (Multiplex Network Body ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Purpose |
|---|---|---|---|
| I162-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I162-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I162-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I162-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.
Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the wire harness connector (I162) to the CAN No. 3 junction connector.
| *1 | DLC3 |
| *a | Component with harness connected
(CAN No. 3 Junction Connector) |
Connect the probes of an ohmmeter to terminals 1 (CANH) and 2 (CANL) of the wire harness connectors (I162) and CG or BAT of the DLC3.
It is only necessary to perform the inspection for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.
While observing the resistance value shown on the ohmmeter, disconnect branch line connectors (I163, I164 and I165) from the CAN No. 3 junction connector or CAN No. 4 junction connector until the resistance becomes normal (6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short)).
| *1 | Main Body ECU (Multiplex Network Body ECU) | *2 | Outer Mirror Control ECU Assembly (for Front Passenger Side) |
| *3 | CAN No. 3 Junction Connector | *4 | Outer Mirror Control ECU Assembly (for Driver Side) |
| *5 | Position Control ECU and Switch Assembly (for Driver Side) | *6 | CAN No. 4 Junction Connector |
| *1 | CAN No. 3 Junction Connector | - | - |
| *a | Junction Connector A Side | *b | Junction Connector B Side |
| *c | Earth Terminal | *d | Front view of wire harness connector
(to CAN No. 3 Junction Connector) |
| CAN No. 3 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
|---|---|---|---|
| Main body ECU (Multiplex network body ECU) | I162 | R | GR |
| Outer mirror control ECU assembly (for Front passenger side) | I163 | G | GR |
| CAN main bus line (bus line connecting CAN No. 3 junction connector and CAN No. 4 junction connector) | I166 | Y | R |
| *1 | CAN No. 4 Junction Connector | - | - |
| *a | Junction Connector A Side | *b | Junction Connector B Side |
| *c | Earth Terminal | *d | Front view of wire harness connector
(to CAN No. 4 Junction Connector) |
| CAN No. 4 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
|---|---|---|---|
| CAN main bus line (bus line connecting CAN No. 3 junction connector and CAN No. 4 junction connector) | I167 | Y | R |
| Position control ECU and switch assembly (for Driver side) | I165 | BE | GR |
| Outer mirror control ECU assembly (for Driver side) | I164 | P | GR |
| Result | Proceed to |
|---|---|
| The resistance between terminals CANP and BAT, or the resistance between terminals CANN and BAT is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector.
(There is no short to +B in the branch lines.) |
A |
| The resistance between terminals CANP and GND, or the resistance between terminals CANN and GND is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector.
(There is no short to GND in the branch lines.) |
|
| The resistance between terminals CANP and BAT, or the resistance between terminals CANN and BAT becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to +B in one of the areas related to one or more of the disconnected branch lines.) |
B |
| The resistance between terminals CANP and GND, or the resistance between terminals CANN and GND becomes normal (200 Ω or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to GND in one of the areas related to one or more of the disconnected branch lines.) |
A
B
Disconnect the wire harness connector (I166) from the CAN No. 3 junction connector.
| *1 | DLC3 |
| *a | Component with harness connected
(CAN No. 3 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Purpose |
|---|---|---|---|
| I162-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I162-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I162-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I162-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.
Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the wire harness connector (I166) to the CAN No. 3 junction connector.
Disconnect the wire harness connector (I167) from the CAN No. 4 junction connector.
| *1 | DLC3 |
| *a | Component with harness connected
(CAN No. 3 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Purpose |
|---|---|---|---|
| I162-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I162-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I162-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I162-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.
Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the connector for the bus line that is shorted to +B or GND to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short) when it was disconnected).
Disconnect the connector that includes terminals CANH and CANL from the ECU to which the bus line shorted to +B or GND is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *1 | DLC3 |
| *a | Component with harness connected
(CAN No. 3 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Purpose |
|---|---|---|---|
| I162-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I162-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I162-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I162-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.
If the resistance becomes normal when the connector is disconnected from the ECU, there may be a short in the ECU.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the main body ECU (multiplex network body ECU) connector.
| *1 | DLC3 |
| *a | Rear view of wire harness connector
(to CAN No. 3 Junction Connector) |
| *b | to Main Body ECU (Multiplex Network Body ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Purpose |
|---|---|---|---|
| I162-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I162-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I162-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I162-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.
Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.
| Result |
|---|
| OK |
| NG |
OK
NG