Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074121 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC circuit is the circuit that goes from the ACC output terminal of the certification ECU (smart key ECU assembly) to the ACC relay.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2274 ACC Monitor Malfunction Malfunction in the ACC relay circuit in the certification ECU (smart key ECU assembly) or in the external circuit (1-trip detection logic*).
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

AM2 fuse

·

ACC relay (Instrument panel junction block assembly)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.

*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the engine switch is off.

·

If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).


HINT:

The engine switch can be turned on (IG) and the engine can be started.


-

WIRING DIAGRAM

B285916E05
0,0.813 0.885,1.302 0.885,0.49 10 false from Battery 1.125,0.969 1.469,1.135 0.344,0.167 10 false AM2 2,0.625 2.094,0.781 0.094,0.156 10 false 2 3.333,0.99 3.427,1.146 0.094,0.156 10 false 4 2.281,0.833 2.49,0.99 0.208,0.156 10 false +B 2.74,1.208 3.167,1.365 0.427,0.156 10 false ACCD 4.833,1.5 5.563,1.656 0.729,0.156 10 false ACC NO. 1 4.833,2.74 5.563,2.896 0.729,0.156 10 false ACC NO. 2 1.865,2.865 3.542,3.229 1.677,0.365 10 false Certification ECU (Smart Key ECU Assembly) 3.823,2.938 6.51,3.094 2.688,0.156 10 false Instrument Panel Junction Block Assembly 2.281,1.615 2.427,1.771 0.146,0.156 10 false E 1.958,1.427 2.135,1.583 0.177,0.156 10 false 11 1.917,0.813 2.26,0.979 0.344,0.167 10 false A43 1.927,1.615 2.271,1.781 0.344,0.167 10 false A43 3.26,1.198 3.604,1.365 0.344,0.167 10 false I78 3.781,1.208 3.979,1.375 0.198,0.167 10 false 3B 3.802,1.042 4.042,1.208 0.24,0.167 10 false 23 3.792,0.604 4.031,0.771 0.24,0.167 10 false 3F 3.823,0.438 3.958,0.604 0.135,0.167 10 false 1 5.74,0.958 6.552,1.167 0.813,0.208 10 false ECU-ACC 5.906,2.083 6.344,2.688 0.438,0.604 10 false SFT LOCK-ACC 6.417,0.604 6.656,0.771 0.24,0.167 10 false 37 6.385,0.792 6.604,0.958 0.219,0.167 10 false 3B 6.417,1.792 6.656,1.958 0.24,0.167 10 false 32 6.458,2.313 6.698,2.479 0.24,0.167 10 false 7 6.396,1.979 6.615,2.146 0.219,0.167 10 false 3A 6.396,2.479 6.615,2.646 0.219,0.167 10 false 3B 0.188,3.052 1.01,3.219 0.823,0.167 10 false *1: for LHD 0.188,3.323 1.01,3.49 0.823,0.167 10 false *2: for RHD 3.792,0.792 4.031,0.958 0.24,0.167 10 false 3E 4.042,0.875 4.281,1.042 0.24,0.167 10 false *1 4.042,0.677 4.281,0.844 0.24,0.167 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2274
Power Source Control
·

ACC Relay Monitor


Starting Control
·

Ignition


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the I78 connector from the certification ECU (smart key ECU assembly).


b.

Disconnect the 3B connector from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I78-4 (ACCD) - 3B-23 Always Below 1 Ω
3B-7 - Body ground Always Below 1 Ω
I78-4 (ACCD) or 3B-23 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B281390C01
4.573,0.198 4.885,0.458 0.313,0.26 2.208,0.094 2.521,0.354 0.313,0.26 4.948,0.198 5.26,0.458 0.313,0.26 4.635,0.229 5.083,0.5 0.448,0.271 10 false 3E 2.281,0.146 2.729,0.417 0.448,0.271 10 false 3B 5.021,0.229 5.469,0.5 0.448,0.271 10 false 3F 4.635,0.01 4.844,0.219 0.208,0.208 10 false *A 5,0.01 5.208,0.219 0.208,0.208 10 false *B 0.094,0 0.375,0.208 0.281,0.208 10 false *a
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
·

3E-1 - 3B-37

·

3E-1 - 3A-32


Battery voltage not applied to terminals 3B-23 and 3B-7 10 kΩ or higher
Battery voltage applied to terminals 3B-23 and 3B-7 Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
·

3F-1 - 3B-37

·

3F-1 - 3A-32


Battery voltage not applied to terminals 3B-23 and 3B-7 10 kΩ or higher
Battery voltage applied to terminals 3B-23 and 3B-7 Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B268626C04
0.124,0.075 0.31,0.237 0.186,0.161 10 *a 1.382,0.285 1.869,0.578 0.487,0.292 1.519,0.343 1.814,0.499 0.296,0.157 10 I78 1.16,1.065 0.869,1.788 false 0.618,1.792 1.089,1.949 0.471,0.157 10 ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the I78 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I78-4 (ACCD) - Body ground Engine switch off → Engine switch on (ACC) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)