Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074122 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Unlock Warning Switch Circuit  


DESCRIPTION

The key unlock warning switch assembly comes on when the ignition key is inserted into the ignition key cylinder and goes off when the ignition key is removed.

WIRING DIAGRAM

B163408E10
2.9,1.24 3.023,1.399 0.124,0.159 10 2 2.642,1.649 2.858,1.808 0.216,0.159 10 I33 2.642,1.805 4.131,2.135 1.488,0.33 10 Unlock Warning Switch Assembly 5.692,2.658 5.904,2.797 0.212,0.139 10 I13 5.692,2.8 6.856,3.271 1.164,0.471 10 Main Body ECU (Multiplex Network Body ECU) 3.78,1.24 3.903,1.399 0.124,0.159 10 1 5.599,1.24 5.771,1.378 0.172,0.138 10 17 5.884,1.356 6.233,1.497 0.349,0.14 10 KSW

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch ON or OFF ON: Key is inserted into ignition key cylinder
OFF: Key is removed from ignition key cylinder
-
Body Electrical > Main Body > Data List
Tester Display
Key Unlock Warning SW
50003 123 32
OK:

When the key is in the ignition key cylinder, "ON" appears on the screen.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.
B289676C02
0.26,0.208 0.521,0.448 0.26,0.24 10 *a 2.938,0.25 3.167,0.51 0.229,0.26 10 *1 2.969,0.771 3.292,1.104 0.323,0.333 10 *2
*1 Free (key removed)
*2 Pushed (key set)
*a Component without harness connected
(Unlock Warning Switch Assembly)


Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Free
(Key removed)
10 kΩ or higher
1 - 2 Pushed
(Key set)
Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - UNLOCK WARNING SWITCH - BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - UNLOCK WARNING SWITCH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I13-17 (KSW) - I33-1 Always Below 1 Ω
I13-17 (KSW) - Body ground Always 10 kΩ or higher
I33-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR