Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074122 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine hood courtesy switch is installed together with the hood lock. This switch turns on when the engine hood is closed and turns off when the engine hood is opened.

WIRING DIAGRAM

B289668E12
5.104,2.688 6.75,3.063 1.646,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 4.01,1.719 5.073,2.208 1.063,0.49 10 false Instrument Panel Junction Block Assembly 5.104,2.542 5.719,2.958 0.615,0.417 10 false MB 5.208,1.01 5.76,1.365 0.552,0.354 10 false HCTY 1.813,1.406 3.646,1.771 1.833,0.365 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 1.813,1.25 2.229,1.667 0.417,0.417 10 false A2 2.271,0.896 2.365,1.042 0.094,0.146 10 false 2 4.938,0.896 5.125,1.042 0.188,0.146 10 false 20 4.177,0.792 4.479,1.104 0.302,0.313 10 false 25 4.177,1 4.448,1.365 0.271,0.365 10 false 3D 3.115,0.896 3.208,1.042 0.094,0.146 10 false 1

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hood Courtesy SW Engine hood courtesy switch ON or OFF ON: Engine hood open
OFF: Engine hood closed
-
Body Electrical > Main Body > Data List
Tester Display
Hood Courtesy SW
50003 123 200
OK:

The indicator on the intelligent tester switches between ON and OFF in accordance with the engine hood courtesy switch (hood lock assembly) status.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B220554C09
1.073,0.51 1.448,0.74 0.375,0.229 4.719,0.51 5.094,0.74 0.375,0.229 5.365,1.26 5.365,1.51 5.365,1.51 5.521,1.51 false 0.146,0.135 0.51,0.385 0.365,0.25 10 *a 1.177,0.563 1.74,0.917 0.563,0.354 10 3D 4.813,0.542 5.302,0.875 0.49,0.333 10 MB 5.542,1.448 6.156,1.781 0.615,0.333 10 HCTY
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 3D instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-25 - MB-20 (HCTY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.INSPECT ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)

b.

Measure the resistance according to the value(s) in the table below.

B348378C01
4,0.896 4.667,0.896 false 2.344,1.073 3.417,1.073 false 4.74,0.781 5.052,0.938 0.313,0.156 10 false *1 2.156,0.948 2.469,1.104 0.313,0.156 10 false *2 3.146,2.938 3.458,3.094 0.313,0.156 10 false *a
*1 Opened *2 Locked
*a Component without harness connected
(Engine Hood Courtesy Switch (Hood Lock Assembly))
- -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Opened 10 kΩ or higher
1 - 2 Locked Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ENGINE HOOD COURTESY SWITCH - BODY GROUND)

NG

REPLACE ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ENGINE HOOD COURTESY SWITCH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-1 - 3D-25 Always Below 1 Ω
A2-1 - Body ground Always 10 kΩ or higher
A2-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR