Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074122 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B289670
2.313,0.969 2.542,1.281 0.229,0.313 10 false 1 2.313,1.615 2.5,1.813 0.188,0.198 10 false 5 3.24,0.969 3.521,1.26 0.281,0.292 10 false 2 3.24,1.625 3.5,1.938 0.26,0.313 10 false 3 5.594,0.958 5.906,1.208 0.313,0.25 10 false 17 4.854,0.865 5.125,1.063 0.271,0.198 10 false 14 1.229,1.208 2,1.521 0.771,0.313 10 false S-HORN 2.563,2.063 3.302,2.302 0.74,0.24 10 false S-HORN 5.875,1.094 6.344,1.458 0.469,0.365 10 false SH 4.844,1.063 5.219,1.323 0.375,0.26 10 false 3D 5.385,3.417 7.021,3.823 1.635,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 1.427,2.583 3.313,2.958 1.885,0.375 10 false Engine Room Relay Block and Junction Block Assembly 4.688,1.677 5.76,2.146 1.073,0.469 10 false Instrument Panel Junction Block Assembly 4.115,4.135 4.323,4.385 0.208,0.25 10 false 1 4.479,4.24 4.844,4.448 0.365,0.208 10 false A44 4.479,4.385 5.344,4.781 0.865,0.396 10 false Security Horn Assembly 0.885,3.844 1.76,4.083 0.875,0.24 10 false from Battery 5.385,3.26 5.823,3.521 0.438,0.26 10 false MB

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Horn Security horn ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Security Horn
50004 123 20
OK:

The security horn assembly sounds and stops correctly when operated through the intelligent tester.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT SECURITY HORN ASSEMBLY
2.INSPECT SECURITY HORN ASSEMBLY
a.
B292917
1.865,1.302 2.021,1.5 0.156,0.198 10 false .

Remove the security horn assembly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY HORN ASSEMBLY>REMOVAL


b.

Check the operation of the security horn assembly.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 Horn sounds
Battery negative (-) → Horn body



Result:
Proceed to
OK
NG



OK

3.INSPECT S-HORN RELAY

NG

3.INSPECT S-HORN RELAY
a.
B256934
2.198,0.917 2.198,0.51 false 2.823,0.99 2.823,0.51 false 2.208,1.875 2.208,1.479 false 2.479,1.875 2.479,1.375 false 0.104,0.083 0.354,0.385 0.25,0.302 10 *a 0.313,1.458 0.479,1.667 0.167,0.208 10 5 1.302,0.656 1.521,0.958 0.219,0.302 10 2 0.313,0.656 0.5,0.938 0.188,0.281 10 1 1.302,1.458 1.479,1.688 0.177,0.229 10 3 2.448,1.885 2.708,2.156 0.26,0.271 10 5 2.167,1.885 2.344,2.094 0.177,0.208 10 1 2.167,0.323 2.323,0.552 0.156,0.229 10 2 2.792,0.323 2.927,0.51 0.135,0.188 10 3
*a S-HORN Relay


Remove the S-HORN relay from engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Condition Condition Specified Condition
3 - 5 When battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 When battery voltage is applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE S-HORN RELAY

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B220554
1.073,0.51 1.448,0.74 0.375,0.229 4.719,0.51 5.094,0.74 0.375,0.229 5,1.25 5,1.5 5,1.5 5.156,1.5 false 0.146,0.135 0.417,0.365 0.271,0.229 10 *a 1.177,0.542 1.49,0.74 0.313,0.198 10 3D 4.802,0.552 5.083,0.76 0.281,0.208 10 MB 5.208,1.427 5.5,1.615 0.292,0.188 10 SH
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-14 - MB-17 (SH) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - S-HORN RELAY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BATTERY - S-HORN RELAY)
a.
B278765
0.177,0.156 0.448,0.417 0.271,0.26 10 *a
*a Engine room relay block and junction block assembly


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly S-HORN relay terminal 1- Body ground Always 11 to 14 V
Engine room relay block and junction block assembly S-HORN relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)
a.
B278765
0.177,0.156 0.448,0.417 0.271,0.26 10 *a
*a Engine room relay block and junction block assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly S-HORN relay terminal 3 - A44-1 Always Below 1 Ω
Engine room relay block and junction block assembly S-HORN relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.
B278765
0.177,0.156 0.448,0.417 0.271,0.26 10 *a
*a Engine room relay block and junction block assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly S-HORN relay terminal 2 - 3D-14 Always Below 1 Ω
Engine room relay block and junction block assembly S-HORN relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR