Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074130 ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the engine switch, the certification ECU (smart key ECU assembly) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B278A Short to GND in Immobiliser System Power Source Circuit A short to GND in the power supply of the transponder key amplifier of the engine switch (VC5 - VC5) (1 trip detection logic*).
·

Wire harness or connector

·

Engine switch

·

Certification ECU (smart key ECU assembly)


DTC output confirmation operation:

With the shift lever in P, the key held near the engine switch and an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P -

Related Data List and Active Test
DTC Code Data List and Active Test
B278A -

WIRING DIAGRAM

B271005E01
0.922,2.986 1.884,3.189 0.962,0.203 10 Engine Switch 0.922,2.818 1.358,2.986 0.437,0.168 10 I58 1.557,1.175 2.032,1.424 0.476,0.249 10 VC5 1.441,2.095 1.895,2.471 0.454,0.375 10 AGND 1.942,1.078 2.192,1.261 0.25,0.183 10 10 1.943,2.01 2.121,2.183 0.179,0.173 10 6 5.061,1.078 5.31,1.261 0.25,0.183 10 1 5.047,2.01 5.296,2.183 0.249,0.173 10 24 5.33,2.087 5.784,2.463 0.454,0.375 10 AGND 5.055,3.006 6.614,3.312 1.559,0.306 10 Certification ECU (Smart Key ECU Assembly) 5.055,2.819 5.461,2.989 0.406,0.17 10 I78 5.344,1.184 5.632,1.563 0.288,0.378 10 VC5

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the I78 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I58 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I78-1 (VC5) - I58-10 (VC5) Always Below 1 Ω
I78-24 (AGND) - I58-6 (AGND) Always Below 1 Ω
I58-10 (VC5) - Body ground Always 10 kΩ or higher
I58-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the I58 engine switch and I78 certification ECU (smart key ECU assembly) connector.


b.
B271009C05
1.313,0.188 1.708,0.448 0.396,0.26 1.833,1.646 2.406,2.031 false 1.198,1.656 0.625,2.052 false 1.417,0.24 1.74,0.427 0.323,0.188 10 I58 0.271,0.219 0.469,0.406 0.198,0.188 10 *a 2.969,3.281 3.302,3.5 0.333,0.219 10 GND 0.281,2.031 0.615,2.188 0.333,0.156 10 VC5 2.469,1.99 2.896,2.146 0.427,0.156 10 AGND
*a Component with harness connected
(Engine Switch)


Using an oscilloscope, check the waveform.

HINT:

Perform this inspection on the engine switch side.


Measurement Condition:
Item Content
Tester Connection I58-10 (VC5) - I58-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed.


OK:

Waveform is output normally (refer to illustration).



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)