Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2011.10–2013.07
RM19V0EQ _58 Vehicle Interior _014612 SEAT BELT _0074172 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

The occupant detection sensor (separate type front seat cushion pad) detects if the passenger seat is occupied and sends signals to the combination meter assembly. The front seat inner belt (for front passenger) detects the passenger seat belt condition and sends signals to the combination meter assembly. After receiving the signals from the occupant detection sensor (separate type front seat cushion pad) and front seat inner belt (for front passenger), the seat belt warning light in the combination meter assembly will blink or go off.

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


WIRING DIAGRAM

B271142E22
0.5,2.031 1.906,2.469 1.406,0.438 10 false Combination Meter Assembly 2.313,1.875 4.667,2.25 2.354,0.375 10 false Occupant Detection Sensor (Separate Type Front Seat Cushion Pad) 4.646,1.177 6.063,1.802 1.417,0.625 10 false Front Seat Inner Belt Assembly (for Front Passenger) 0.531,1.854 0.906,2.063 0.375,0.208 10 false I18 1.208,0.781 1.74,1.177 0.531,0.396 10 false P/SB 1.646,0.688 1.938,1.052 0.292,0.365 10 false 20 2.677,0.594 2.948,0.844 0.271,0.25 10 false 3 2.792,1.156 2.896,1.292 0.104,0.135 10 false 1 3.052,1.135 3.25,1.365 0.198,0.229 10 false B 3.781,1.156 3.99,1.438 0.208,0.281 10 false 3 4.042,1.135 4.292,1.5 0.25,0.365 10 false B 2.625,0.771 2.896,1.177 0.271,0.406 10 false N2 5.625,0.771 6.021,1.146 0.396,0.375 10 false N2 5.677,0.583 5.927,0.833 0.25,0.25 10 false 2

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger seat belt buckle switch signal ON or OFF ON: Front passenger seat belt fastened
OFF: Front passenger seat belt not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
P-Seatbelt Buckle SW
50003 122 7

OK:

ON or OFF appears on the tester screen according to the front passenger seat belt condition.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT SEAT INNER BELT - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT SEAT INNER BELT - BODY GROUND)
a.

Disconnect the I18 combination meter assembly connector.


b.

Disconnect the N2 front seat inner belt assembly (for front passenger) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-20 (P/SB) - N2-3 Always Below 1 Ω
I18-20 (P/SB) - Body ground Always 10 kΩ or higher
N2-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)
a.
B218574C23
0.146,0.125 0.303,0.276 0.157,0.152 10 *a
*a Component without harness connected
(Occupant Detection Sensor (Separate Type Front Seat Cushion Pad))


Remove the occupant detection sensor (separate type front seat cushion pad).

Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 3 Front passenger seat occupied Below 100 Ω
1 - 3 Front passenger seat not occupied 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER)

NG

REPLACE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)

4.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER)
a.
B271152C25
1.521,0.406 1.906,0.656 0.385,0.25 1.542,2.823 1.927,3.073 0.385,0.25 0.177,0.104 0.448,0.469 0.271,0.365 10 false *a 1.604,0.448 2.354,0.927 0.75,0.479 10 false N2 1.677,2.865 2.333,3.24 0.656,0.375 10 false B
*a Component without harness connected
(Front Seat Inner Belt Assembly (for Front Passenger))


Remove the front seat inner belt assembly (for front passenger).

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for RHD)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-3 - B-1 Always Below 1 Ω
N2-2 - B-3 Front passenger seat belt unfastened Below 1 Ω
N2-2 - B-3 Front passenger seat belt fastened 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER)