Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM19V0EQ _58 Vehicle Interior _014613 HEATING / AIR CONDITIONING _0074197 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1412/12  Ambient Temperature Sensor Circuit  


DESCRIPTION

The ambient temperature sensor (thermistor assembly) is installed in front of the condenser to detect the ambient temperature which is used to control the air conditioning system AUTO mode. This sensor is connected to the air conditioning amplifier assembly and detects fluctuations in the ambient temperature. This data is used for controlling the cabin temperature. The sensor sends a signal to the air conditioning amplifier assembly. The resistance of the ambient temperature sensor (thermistor assembly) changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies a voltage (5 V) to the ambient temperature sensor (thermistor assembly) and reads voltage changes due to changes in to the resistance of the ambient temperature sensor (thermistor assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1412/12 Ambient Temperature Sensor Circuit Open or short in ambient temperature sensor (thermistor assembly) circuit
·

Ambient temperature sensor (thermistor assembly)

·

Harness or connector between ambient temperature sensor (thermistor assembly) and air conditioning amplifier assembly

·

Air conditioning amplifier assembly


Memorized
(4 sec. or more)*1

*1: The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.


HINT:

If the ambient temperature is approx. -52.9°C (-63.22°F) or lower, DTC B1412/12 may be output even though the system is normal.


WIRING DIAGRAM

E236722
2.146,0.458 2.24,0.635 0.094,0.177 10 false 2 2.146,1.406 2.24,1.583 0.094,0.177 10 false 1 1.958,0.458 2.073,0.635 0.115,0.177 10 false + 1.99,1.406 2.073,1.583 0.083,0.177 10 false - 5.115,0.458 5.292,0.635 0.177,0.177 10 false 5 5.115,1.417 5.292,1.594 0.177,0.177 10 false 13 5.417,0.552 5.74,0.729 0.323,0.177 10 false TAM 5.417,1.5 5.76,1.677 0.344,0.177 10 false SG-2 0.833,1.792 1.156,1.969 0.323,0.177 10 false A3 0.833,1.948 2.656,2.354 1.823,0.406 10 false Ambient Temperature Sensor (Thermistor Assembly) 5.063,1.875 5.344,2.052 0.281,0.177 10 false I77 5.063,2.031 6.635,2.458 1.573,0.427 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ambient Temp Sensor Ambient temperature sensor (thermistor assembly) Min: -23.30°C (-9.94°F)
Max: 65.95°C (150.71°F)
Actual ambient temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Ambient Temp Sensor
50003 121 2
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

2.INSPECT AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY)

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.INSPECT AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY)
a.
E202729
0.427,0.323 0.729,0.573 0.302,0.25 1.521,3.031 1.938,2.615 false 3.083,1.281 2.917,0.552 false 1.458,0.885 1.292,0.542 false 1.031,0.865 1.177,0.542 false 0.49,0.365 0.75,0.604 0.26,0.24 10 false A3 3.083,1.323 3.313,1.542 0.229,0.219 10 false *b 0.135,2.781 0.365,3 0.229,0.219 10 false *c 1.958,4.25 2.188,4.469 0.229,0.219 10 false *d 1.938,2.417 2.167,2.635 0.229,0.219 10 false *e 0.927,0.875 1.156,1.094 0.229,0.219 10 false + 1.458,0.885 1.604,1.115 0.146,0.229 10 false - 0.125,0.135 0.354,0.354 0.229,0.219 10 false *a
*a Component without harness connected
(Ambient Temperature Sensor (Thermistor Assembly))
*b Sensing Portion
*c Resistance (kΩ)
*d Temperature (°C (°F))
*e Allowable Range


Remove the ambient temperature sensor (thermistor assembly).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>REMOVAL


b.

Disconnect the A3 ambient temperature sensor (thermistor assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A3-1 (-) - A3-2 (+) 10°C (50°F) 3.00 to 3.73 kΩ
A3-1 (-) - A3-2 (+) 15°C (59°F) 2.45 to 2.88 kΩ
A3-1 (-) - A3-2 (+) 20°C (68°F) 1.95 to 2.30 kΩ
A3-1 (-) - A3-2 (+) 25°C (77°F) 1.60 to 1.80 kΩ
A3-1 (-) - A3-2 (+) 30°C (86°F) 1.28 to 1.47 kΩ
A3-1 (-) - A3-2 (+) 35°C (95°F) 1.00 to 1.22 kΩ
A3-1 (-) - A3-2 (+) 40°C (104°F) 0.80 to 1.00 kΩ
A3-1 (-) - A3-2 (+) 45°C (113°F) 0.65 to 0.85 kΩ
A3-1 (-) - A3-2 (+) 50°C (122°F) 0.50 to 0.70 kΩ
A3-1 (-) - A3-2 (+) 55°C (131°F) 0.44 to 0.60 kΩ
A3-1 (-) - A3-2 (+) 60°C (140°F) 0.36 to 0.50 kΩ


NOTICE:
·

Hold the sensor only by its connector. Touching the sensor may change the resistance value.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (see the graph).



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPLACE AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR (THERMISTOR ASSEMBLY) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the I77 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I77-5 (TAM) - A3-2 (+) Always Below 1 Ω
I77-13 (SG-2) - A3-1 (-) Always Below 1 Ω
I77-5 (TAM) - Body ground Always 10 kΩ or higher
I77-13 (SG-2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR