Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM19V0EQ _59 Vehicle Exterior _014616 WINDOW / GLASS _0074215 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

w/ Jam Protection Function on Driver Door:

When the ignition switch is ON, the power window regulator motor assembly (for driver door) is operated by the power window regulator master switch assembly. The power window regulator motor assembly (for driver door) has motor, regulator and ECU functions.


w/o Jam Protection Function on Driver Door:

When the ignition switch is ON, the power window regulator motor assembly (for driver door) is operated by the power window regulator master switch assembly.


WIRING DIAGRAM

w/ Jam Protection Function on Driver Door


B281016
0.427,2.281 2.083,2.719 1.656,0.438 10 false Main Body ECU (Multiplex Network Body ECU) 0.979,3.375 2.74,3.635 1.76,0.26 10 false : LIN Communication Line 0.469,0.51 1.417,0.802 0.948,0.292 10 false from Battery 1.75,0.667 2.771,0.938 1.021,0.271 10 false DOOR NO. 2 2.521,2.396 4.469,2.792 1.948,0.396 10 false Power Window Regulator Motor Assembly (for Driver Door) 5.229,2.385 6.823,2.813 1.594,0.427 10 false Power Window Regulator Master Switch Assembly 6.177,3.052 6.917,3.25 0.74,0.198 10 false *1: for LHD 6.177,3.365 6.927,3.563 0.75,0.198 10 false *2: for RHD 2.521,2.24 3.281,2.469 0.76,0.229 10 false K9*1, J9*2 5.229,2.229 6.115,2.49 0.885,0.26 10 false K10*1, J10*2 1.635,1.583 2.063,1.781 0.427,0.198 10 false LIN2 2.833,1.448 3.229,1.688 0.396,0.24 10 false LIN 2.844,0.427 3.083,0.667 0.24,0.24 10 false B 3.771,0.427 4.281,0.729 0.51,0.302 10 false AUTO 5.375,0.542 5.677,0.792 0.302,0.25 10 false A 5.375,1.042 5.625,1.271 0.25,0.229 10 false D 5.375,1.542 5.615,1.75 0.24,0.208 10 false U 5.375,1.844 5.646,2.063 0.271,0.219 10 false E 3.75,0.938 4.333,1.188 0.583,0.25 10 false DWN1 3.885,1.438 4.323,1.677 0.438,0.24 10 false UP1 4.042,1.719 4.26,1.979 0.219,0.26 10 false E 4.26,1.719 4.479,2.01 0.219,0.292 10 false 1 4.271,0.938 4.573,1.271 0.302,0.333 10 false 7 5.198,0.938 5.469,1.167 0.271,0.229 10 false 5 4.792,1.438 5.427,1.688 0.635,0.25 10 false 8*1, 1*2 4.792,1.708 5.448,1.99 0.656,0.281 10 false 1*1, 9*2 4.271,0.427 4.469,0.708 0.198,0.281 10 false 4 5.198,0.427 5.49,0.667 0.292,0.24 10 false 4 4.229,1.438 4.521,1.667 0.292,0.229 10 false 10 2.635,0.427 2.885,0.698 0.25,0.271 10 false 2 2.635,1.448 2.854,1.698 0.219,0.25 10 false 9


w/o Jam Protection Function on Driver Door


B281027
4.552,3.094 6.104,3.479 1.552,0.385 10 false Power Window Regulator Master Switch Assembly 0.24,2.823 2.188,3.219 1.948,0.396 10 false Power Window Regulator Motor Assembly (for Driver Door) 4.552,2.927 5.01,3.219 0.458,0.292 10 false K10 0.24,2.667 0.729,3.031 0.49,0.365 10 false K14 6.188,2.26 6.458,2.563 0.271,0.302 10 false E 6.365,2.25 6.615,2.5 0.25,0.25 10 false 1 5.219,1.635 5.469,1.969 0.25,0.333 10 false B 5.396,1.427 5.771,1.771 0.375,0.344 10 false 6 4.375,2.073 4.604,2.333 0.229,0.26 10 false U 1.344,2.063 1.646,2.354 0.302,0.292 10 false U 1.51,2.063 1.875,2.385 0.365,0.323 10 false 1 4.375,2.396 4.667,2.656 0.292,0.26 10 false D 1.344,2.375 1.604,2.625 0.26,0.25 10 false D 1.51,2.375 1.708,2.573 0.198,0.198 10 false 2 4.219,2.073 4.552,2.365 0.333,0.292 10 false 3 4.219,2.385 4.469,2.625 0.25,0.24 10 false 4 1.99,0.875 3.094,1.417 1.104,0.542 10 false DOOR NO. 1 0.271,0.75 1.698,1.208 1.427,0.458 10 false from DOOR Relay


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.*

·

If a power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).*

·

When the ECU determines that the power window regulator motor assembly (for driver door) has a malfunction, DTC B2311 is stored.*


*: w/ Jam Protection Function on Driver Door



PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
w/ Jam Protection Function on Driver Door A
w/o Jam Protection Function on Driver Door B



A

2.READ VALUE USING INTELLIGENT TESTER (MAIN BODY)

B

8.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
2.READ VALUE USING INTELLIGENT TESTER (MAIN BODY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Communication D-Door Motor Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) OK or STOP OK: Normal communication
STOP: Communication stopped
-
Body Electrical > Main Body > Data List
Tester Display
Communication D-Door Motor
50003 123 49
OK:

On the intelligent tester screen, OK is displayed.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)

NG

GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting)

3.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
a.

Enter the following menus: Body / D-Door Motor / Data List.


b.

Read the Data List according to the display on the intelligent tester.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal ON or OFF ON: Driver door power window manual up switch operated
OFF: Driver door power window manual up switch not operated
-
D Door P/W Down SW Driver door power window manual down switch signal ON or OFF ON: Driver door power window manual down switch operated
OFF: Driver door power window manual down switch not operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
D Door P/W Down SW
50003 124 2,3
OK:

On the intelligent tester screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)

NG

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR) - BATTERY AND BODY GROUND)
4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
a.

Enter the following menus: Body / D-Door Motor / Active Test.


b.

Perform the Active Test according to the display on the intelligent tester.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


Body Electrical > D-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Power window OFF / UP / DOWN -
Body Electrical > D-Door Motor > Active Test
Tester Display
Power Window
50004 124 1
OK:

Driver door power window operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR) - BATTERY AND BODY GROUND)
a.

Disconnect the power window regulator motor assembly (for driver door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
K9-2 (B) - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
J9-2 (B) - Body ground Always 11 to 14 V


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K9-1 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
J9-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER) AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER) AND BODY GROUND)
a.

Disconnect the power window regulator master switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K10-8 (U) - K9-10 (UP1) Always Below 1 Ω
K10-5 (D) - K9-7 (DWN1) Always Below 1 Ω
K10-8 (U) - Body ground Always 10 kΩ or higher
K10-5 (D) - Body ground Always 10 kΩ or higher
K10-1 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
J10-1 (U) - J9-10 (UP1) Always Below 1 Ω
J10-5 (D) - J9-7 (DWN1) Always Below 1 Ω
J10-1 (U) - Body ground Always 10 kΩ or higher
J10-5 (D) - Body ground Always 10 kΩ or higher
J10-9 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B164359
2.365,1.781 2.656,2.635 false 1.75,1.781 1.479,2.635 false 1.229,1.792 0.938,2.625 false 1.063,1.792 0.354,2.635 false 0.188,0.156 0.719,0.719 0.531,0.563 10 false *a 0.802,2.656 1.323,2.969 0.521,0.313 10 false U*A 0.198,2.667 0.74,3.01 0.542,0.344 10 false E*B 1.385,2.646 1.625,2.917 0.24,0.271 10 false D 2.375,2.667 3.115,2.969 0.74,0.302 10 false E*A,U*B
*A for LHD
*B for RHD
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
8 (U) - 1 (E) Manual UP Below 1 Ω
5 (D) - 1 (E) Manual DOWN Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
1 (U) - 9 (E) Manual UP Below 1 Ω
5 (D) - 9 (E) Manual DOWN Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the power window regulator master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K10-6 (B) - Body ground Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
K10-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR))
a.

Disconnect the power window regulator motor assembly (for driver door) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-3 (U) - K14-1 (U) Always Below 1 Ω
K10-4 (D) - K14-2 (D) Always Below 1 Ω
K10-3 (U) - Body ground Always 10 kΩ or higher
K10-4 (D) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)
a.
B127535
0.083,0.083 0.438,0.396 0.354,0.313 10 *a 1.573,0.948 1.833,1.25 0.26,0.302 10 *c 1.25,1.646 1.667,1.927 0.417,0.281 10 *d 0.729,0.26 1.052,0.552 0.323,0.292 10 *b
*a Component without harness connected
(Power Window Regulator Motor Assembly)
*b Motor Gear
*c Counterclockwise
*d Clockwise


Remove the power window regulator motor assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL


b.

Apply battery voltage to the motor connector according to the table below.

NOTICE:

Do not apply battery voltage to any terminals except terminals 1 and 2.


Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Motor gear rotates clockwise
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Motor gear rotates counterclockwise



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)