Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM19V0EQ _59 Vehicle Exterior _014616 WINDOW / GLASS _0074215 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Key-off Operation Function Operates even if Operating Conditions are not Satisfied  


DESCRIPTION

·

When the front doors are closed, each power window regulator motor assembly can control its power window operation for approximately 43 seconds after the ignition switch is turned from ON to off by receiving operation permission signals from the main body ECU (multiplex network body ECU).

·

However, when approximately 43 seconds have elapsed, or the driver door or front passenger door is opened within approximately 43 seconds of the ignition switch being turned off, the power window regulator motor assembly stops operating.

·

During an auto operation, when 43 seconds have passed and key-off operation is prohibited, the window continues the operation until the auto operation is completed.


CAUTION / NOTICE / HINT

NOTICE:

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.


PROCEDURE

1.CHECK MANUAL UP / DOWN FUNCTION
a.

Check that the manual up and down functions using the power window regulator master switch assembly and power window regulator switch assembly can operate all the power windows.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK

OK:

Manual up and down functions are normal.



Result:
Proceed to
OK
NG



OK

2.CHECK REMOTE UP / DOWN FUNCTION

NG

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)

2.CHECK REMOTE UP / DOWN FUNCTION
a.

Check that the remote up and down functions using the power window regulator master switch assembly can operate all the power windows.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK

OK:

Remote up and down functions are normal.



Result:
Proceed to
OK
NG



OK

3.CHECK OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF

NG

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)

3.CHECK OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF
a.

Check the power window operation function after the ignition switch is turned off.


Result:
Result Proceed to
When power window can still be operated even after opening driver door or front passenger door within approximately 43 seconds of ignition switch being turned off A
When power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (for All Doors)*1 B
When power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (for Driver Door)*1 C
When power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (Front Passenger Door, Rear LH Door or Rear RH Door)*1 D
When power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (for All Doors)*2


*1: w/ Jam Protection Function on Driver Door

*2: w/o Jam Protection Function on Driver Door



A

4.READ VALUE USING INTELLIGENT TESTER

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

D

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
4.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy Front door courtesy light switch RH ON or OFF ON: Front door RH closed
OFF: Front door RH open
-
FL Door Courtesy Front door courtesy light switch LH ON or OFF ON: Front door LH closed
OFF: Front door LH open
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy
FL Door Courtesy
50003 123 197,199
OK:

On the intelligent tester screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Proceed to Front Door Courtesy Switch Circuit)

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK POWER WINDOW CONTROL SYSTEM
6.CHECK POWER WINDOW CONTROL SYSTEM
a.

Check the power window operation function after the ignition switch is turned off.

OK:

The power window control system operates normally.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY