Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM19V0EQ _59 Vehicle Exterior _014616 WINDOW / GLASS _0074215 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Door Power Window does not Operate with Driver Side Door Key Cylinder or Wireless Transmitter  


DESCRIPTION

Wireless Transmitter-linked Function
·

w/ Smart Entry and Start System:

When a key switch is pushed: 1) the door control receiver receives the wireless door lock signal; 2) the door control receiver sends a signal to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly); 3) the main body ECU (multiplex network body ECU) sends the operation permission signal to the power window regulator motor assembly (for driver door); and 4) the power window regulator motor assembly (for driver door) is activated.

·

w/o Smart Entry and Start System:

When a key switch is pushed: 1) a door control receiver receives the wireless door lock signal; 2) the door control receiver sends a signal to the main body ECU (multiplex network body ECU); 3) the main body ECU (multiplex network body ECU) sends the operation permission signal to the power window regulator motor assembly (for driver door); and 4) the power window regulator motor assembly (for driver door) is activated.


Key-linked Function

When the driver door key cylinder (key linked switch) is turned: 1) the door lock motor receives the signal; 2) the main body ECU (multiplex network body ECU) sends the signal to the power window regulator motor assembly (for driver door); and 3) the power window regulator motor assembly (for driver door) is activated.


CAUTION / NOTICE / HINT

NOTICE:
·

This function is set through the customize function, as it is off by default.

·

The power window control system uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.



PROCEDURE

1.CHECK BASIC FUNCTION (WIRELESS AND POWER DOOR LOCK CONTROL SYSTEM)
a.

Check that the wireless door lock/unlock function operates normally (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK for vehicle with Smart Entry and Start System, See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)>OPERATION CHECK for vehicle without Smart Entry and Start System).


b.

Check that the key-linked lock/unlock function operates normally.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock/unlock function and key-linked lock/unlock function operate normally A
Wireless door lock/unlock function does not operate normally (w/ Smart Entry and Start System) B
Wireless door lock/unlock function does not operate normally (w/o Smart Entry and Start System) C
Key-linked lock/unlock function does not operate normally D



A

2.CHECK MANUAL UP / DOWN FUNCTION

B

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table)

C

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table)

D

GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table)

2.CHECK MANUAL UP / DOWN FUNCTION
a.

Check that the manual up and down functions using the power window regulator master switch assembly can operate the driver door power window.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK

OK:

Manual up and down functions are normal.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)