Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM19V0EQ _59 Vehicle Exterior _014617 SLIDING ROOF / CONVERTIBLE _0074219 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2342  Switch Failure  


DESCRIPTION

This DTC is stored when the sliding roof ECU (sliding roof drive gear sub-assembly) detects that the sliding roof switch is stuck for 30 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2342 Switch Failure Sliding roof ECU (sliding roof drive gear sub-assembly) detects sliding roof switch is stuck for 30 seconds or more.
·

Sliding roof ECU (Sliding roof drive gear sub-assembly)

·

Sliding roof switch (Roof console box assembly)

·

Wire harness or connector



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, it requires initialization (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Sliding Roof / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch Failure(Past) Open switch failure signal (Past) ON or OFF ON: Sliding roof open switch failure signal (Past)
OFF: No sliding roof open switch failure signal (Past)
-
Close Switch Failure(Past) Close switch failure signal (Past) ON or OFF ON: Sliding roof close switch failure signal (Past)
OFF: No sliding roof close switch failure signal (Past)
-
Up Switch Failure(Past) Up switch failure signal (Past) ON or OFF ON: Sliding roof tilt up switch failure signal (Past)
OFF: No sliding roof tilt up switch failure signal (Past)
-
Down Switch Failure(Past) Down switch failure signal (Past) ON or OFF ON: Sliding roof tilt down switch failure signal (Past)
OFF: No sliding roof tilt down switch failure signal (Past)
-
Open Switch Failure(Current) Open switch failure signal (Current) ON or OFF ON: Sliding roof open switch failure signal (Current)
OFF: No sliding roof open switch failure signal (Current)
-
Close Switch Failure(Current) Close switch failure signal (Current) ON or OFF ON: Sliding roof close switch failure signal (Current)
OFF: No sliding roof close switch failure signal (Current)
-
Up Switch Failure(Current) Up switch failure signal (Current) ON or OFF ON: Sliding roof tilt up switch failure signal (Current)
OFF: No sliding roof tilt up switch failure signal (Current)
-
Down Switch Failure(Current) Down switch failure signal (Current) ON or OFF ON: Sliding roof tilt down switch failure signal (Current)
OFF: No sliding roof tilt down switch failure signal (Current)
-
Body Electrical > Sliding Roof > Data List
Tester Display
Open Switch Failure(Past)
Close Switch Failure(Past)
Up Switch Failure(Past)
Down Switch Failure(Past)
Open Switch Failure(Current)
Close Switch Failure(Current)
Up Switch Failure(Current)
Down Switch Failure(Current)
50003 147 32,33,34,35,36,37,38,39
OK:

"OFF" appears on the intelligent tester screen.



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BODY GROUND)
a.

Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


b.

Disconnect the S7 sliding roof switch (roof console box assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S4-7 (OPN) - Body ground Always 10 kΩ or higher
S4-6 (DWN) - Body ground Always 10 kΩ or higher
S4-5 (CLS) - Body ground Always 10 kΩ or higher
S4-4 (UP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY)
a.
B270995
1.792,3.833 1.792,3.354 1.792,3.354 1.625,3.354 false 2.146,3.833 2.146,3.354 2.146,3.354 2.302,3.354 false 2.021,3.833 2.021,3.104 2.021,3.104 2.167,3.104 false 1.896,3.833 1.896,3.104 1.896,3.104 1.75,3.104 false 2.302,3.885 2.625,3.885 false 0.51,3 0.688,3.156 0.177,0.156 10 *a 1.365,3.271 1.583,3.427 0.219,0.156 10 UP 1.188,3.031 1.656,3.188 0.469,0.156 10 DOWN 2.208,3.031 2.531,3.188 0.323,0.156 10 OPN 2.333,3.271 2.656,3.427 0.323,0.156 10 CLS 2.646,3.802 3,3.958 0.354,0.156 10 GND
*a Component without harness connected
(Sliding Roof Switch (Roof Console Box Assembly))


Remove the sliding roof switch (roof console box assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (UP) - 1 (GND) UP switch is pressed Below 1 Ω
5 (UP) - 1 (GND) UP switch is not pressed 10 kΩ or higher
4 (DOWN) - 1 (GND) DOWN switch is pressed Below 1 Ω
4 (DOWN) - 1 (GND) DOWN switch is not pressed 10 kΩ or higher
3 (OPN) - 1 (GND) OPEN switch is pressed Below 1 Ω
3 (OPN) - 1 (GND) OPEN switch is not pressed 10 kΩ or higher
2 (CLS) - 1 (GND) CLOSE switch is pressed Below 1 Ω
2 (CLS) - 1 (GND) CLOSE switch is not pressed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPLACE SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY)