Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM SYSTEM › 2011.10–2015.04
RM19V0EQ _59 Vehicle Exterior _014621 LIGHTING (EXT) _0074247 AUTOMATIC HIGH BEAM SYSTEM C

LIGHTING (EXT)  AUTOMATIC HIGH BEAM SYSTEM  B124D  Lost Communication with AFS LIN  B2432  Lost Communication with Automatic High Beam Sensor  


DESCRIPTION

·

DTC B124D is stored when the main body ECU (multiplex network body ECU) detects malfunctions in the LIN communication system.

·

DTC B2432 is stored when the AFS ECU (headlight swivel ECU assembly) detects malfunctions in the LIN communication system.


DTC No. Detection Item DTC Detection Condition Trouble Area
B124D Lost Communication with AFS LIN Malfunction in LIN communication system
·

Inner rear view mirror assembly

·

Harness or connector

·

AFS ECU (headlight swivel ECU assembly)


B2432 Lost Communication with Automatic High Beam Sensor Malfunction in LIN communication system
·

Inner rear view mirror assembly

·

Harness or connector

·

AFS ECU (headlight swivel ECU assembly)



WIRING DIAGRAM

E196370E05
5.469,2.01 7.135,2.469 1.667,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 2.25,2.021 3.958,2.427 1.708,0.406 10 false AFS ECU (Headlight Swivel ECU Assembly) 0.323,1.969 1.698,2.344 1.375,0.375 10 false Inner Rear View Mirror Assembly 0.313,1.802 0.635,2 0.323,0.198 10 false S2 1.333,1.167 1.573,1.323 0.24,0.156 10 false LIN 1.656,1.021 1.844,1.177 0.188,0.156 10 false 5 2.24,1.021 2.427,1.177 0.188,0.156 10 false 11 3.656,0.677 3.844,0.833 0.188,0.156 10 false 12 3.656,1.26 3.844,1.417 0.188,0.156 10 false 13 5.427,0.677 5.615,0.833 0.188,0.156 10 false 14 5.438,1.26 5.615,1.417 0.177,0.156 10 false 13 2.5,1.177 2.844,1.333 0.344,0.156 10 false RHE 3.208,0.833 3.635,1.052 0.427,0.219 10 false MPX1 3.208,1.417 3.635,1.698 0.427,0.281 10 false MPX2 5.688,0.833 6.115,0.99 0.427,0.156 10 false CANH 5.688,1.417 6.115,1.573 0.427,0.156 10 false CANL 2.25,1.844 2.615,2 0.365,0.156 10 false A35 5.479,1.844 5.844,2 0.365,0.156 10 false I13 0.813,2.917 2.135,3.104 1.323,0.188 10 false : LIN Communication 0.781,3.25 2.24,3.438 1.458,0.188 10 false : CAN Communication 1.458,1.5 1.646,1.656 0.188,0.156 10 false E 1.656,1.375 1.844,1.531 0.188,0.156 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before performing the following inspection.


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HIGH BEAM SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123
Body Electrical > AFS > Clear DTCs
50002 165

b.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HIGH BEAM SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123
Body Electrical > AFS > Trouble Codes
50001 165
OK:

DTC B124D or B2432 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (AFS ECU - INNER REAR VIEW MIRROR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (AFS ECU - INNER REAR VIEW MIRROR ASSEMBLY)
a.

Disconnect the A35 AFS ECU (headlight swivel ECU assembly) connector.


b.

Disconnect the S2 inner rear view mirror assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-11 (RHT) - S2-5 (LIN) Always Below 1 Ω
S2-5 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY)
a.

Reconnect the A35 AFS ECU (headlight swivel ECU assembly) connector.


b.
E233264C01
0.198,0.082 0.409,0.27 0.212,0.189 10 *a 0.971,1.649 1.134,1.837 0.163,0.189 10 E 2.1,1.649 2.381,1.837 0.281,0.189 10 LIN 1.316,1.251 1.076,1.634 false 2.044,1.251 2.216,1.634 false 1.573,0.291 1.791,0.455 0.219,0.164 10 S2 1.507,0.255 1.872,0.499 0.365,0.244
*a Front view of wire harness connector
(to Inner Rear View Mirror Assembly)


Connect an oscilloscope to the S2 inner rear view mirror assembly connector.


c.
E177995E08
2.857,1.753 3.208,1.909 0.351,0.156 10 GND

Check the waveform.

OK:
Tester Connection Tool Setting Condition Specified Condition
S2-5 (LIN) - S2-1 (E) 2 V/DIV., 20 ms./DIV. Ignition switch ON Correct waveform is as shown



Result:
Proceed to
OK
NG



OK

REPLACE INNER REAR VIEW MIRROR ASSEMBLY

NG

REPLACE AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY)