Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM19V0EQ _59 Vehicle Exterior _014621 LIGHTING (EXT) _0074248 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects the ambient light. The sensor creates an electrical signal based on the amount of light, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1244 Light Sensor Circuit Malfunction
·

Malfunction in automatic light control sensor

·

Open or short in automatic light control sensor circuit


·

Automatic light control sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

E223761E15
0.583,2.635 1.448,2.823 0.865,0.188 10 false I61*1, I159*2 0.583,2.813 2.583,3 2,0.188 10 false Automatic Light Control Sensor 4.927,2.823 6.573,3.219 1.646,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 4.927,2.656 5.198,2.823 0.271,0.167 10 false I13 1.625,0.844 2.042,1.052 0.417,0.208 10 false CLTB 1.625,2.167 2.146,2.427 0.521,0.26 10 false CLTS 1.625,1.51 2.146,1.781 0.521,0.271 10 false CLTE 2.073,0.75 2.323,0.927 0.25,0.177 10 false 6*1 2.073,2.073 2.344,2.271 0.271,0.198 10 false 5*1 2.073,1.417 2.333,1.615 0.26,0.198 10 false 3*1 2.073,0.969 2.323,1.146 0.25,0.177 10 false 3*2 2.073,2.292 2.333,2.521 0.26,0.229 10 false 4*2 2.073,1.625 2.323,1.771 0.25,0.146 10 false 5*2 5.031,0.854 5.427,1.01 0.396,0.156 10 false CLTB 5.031,1.51 5.427,1.667 0.396,0.156 10 false CLTE 5.031,2.167 5.427,2.323 0.396,0.156 10 false CLTS 4.75,0.729 4.938,0.875 0.188,0.146 10 false 20 4.76,1.406 5,1.656 0.24,0.25 10 false 22 4.75,2.063 4.99,2.25 0.24,0.188 10 false 21 2.104,3.156 4.802,3.323 2.698,0.167 10 false *1: for Automatic Air Conditioning System 2.115,3.427 4.656,3.625 2.542,0.198 10 false *2: for Manual Air Conditioning System

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Illumination Rate Info Illumination rate information 0.00 ms. to 2162.65 ms. Value is output according to ambient light levels -
Body Electrical > Main Body > Data List
Tester Display
Illumination Rate Info
50003 123 61
OK:

Normal condition listed above is displayed.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the I61*1 or I159*2 automatic light control sensor connector.

*1: for Automatic Air Conditioning System

*2: for Manual Air Conditioning System



b.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Air Conditioning System
Tester Connection Condition Specified Condition
I13-22 (CLTE) - I61-3 (CLTE) Always Below 1 Ω
I13-21 (CLTS) - I61-5 (CLTS) Always Below 1 Ω
I13-20 (CLTB) - I61-6 (CLTB) Always Below 1 Ω
I13-22 (CLTE) - Body ground Always 10 kΩ or higher
I13-21 (CLTS) - Body ground Always 10 kΩ or higher
I13-20 (CLTB) - Body ground Always 10 kΩ or higher

for Manual Air Conditioning System
Tester Connection Condition Specified Condition
I13-22 (CLTE) - I159-5 (CLTE) Always Below 1 Ω
I13-21 (CLTS) - I159-4 (CLTS) Always Below 1 Ω
I13-20 (CLTB) - I159-3 (CLTB) Always Below 1 Ω
I13-22 (CLTE) - Body ground Always 10 kΩ or higher
I13-21 (CLTS) - Body ground Always 10 kΩ or higher
I13-20 (CLTB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
E173035C09
1.542,0.823 1.906,1.094 0.365,0.271 2.083,2 1.365,2.813 false 2.458,2.01 2.458,2.813 false 0.146,0.115 0.854,0.708 0.708,0.594 10 *a 1.083,2.833 1.771,3.208 0.688,0.375 10 CLTE 2.271,2.833 2.781,3.115 0.51,0.281 10 CLTB 1.635,0.875 2.104,1.302 0.469,0.427 10 I13
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))


Reconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I13-20 (CLTB) - I13-22 (CLTE) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
I13-22 (CLTE) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.
E161973C04
1.5,0.594 1.896,0.854 0.396,0.26 1.938,2.177 2.51,2.51 false 1.938,1.927 2.51,1.594 false 0.104,0.094 0.979,0.844 0.875,0.75 10 *a 2.542,2.438 3.354,2.854 0.813,0.417 10 CLTS 2.542,1.5 3.25,1.938 0.708,0.438 10 CLTE 1.583,0.635 2.208,1.167 0.625,0.531 10 I61
*a Component with harness connected
(Automatic Light Control Sensor)


for Automatic Air Conditioning System

i.

Reconnect the I61 automatic light control sensor connector.


ii.

Connect an oscilloscope to the automatic light control sensor connector.


iii.
B113714E14
2.948,1.063 3.427,1.448 0.479,0.385 10 GND 1.844,1.177 2.438,1.604 0.594,0.427 10 A

Check the waveform.

OK:
Tester Connection Tool Setting Condition Specified Condition
I61-3 (CLTE) - I61-5 (CLTS) 5 V/DIV., 5 ms./DIV. Ignition switch ON, light control switch in AUTO position Correct waveform is as shown


HINT:

If the ambient light becomes brighter, width A becomes narrower.




b.
E236974C09
0.174,0.147 0.377,0.303 0.203,0.156 10 *a 0.433,1.47 0.823,1.615 0.39,0.145 10 CLTS 0.422,2.448 0.807,2.593 0.385,0.145 10 CLTE 0.925,1.568 1.502,1.899 false 1.477,0.577 1.949,0.874 0.471,0.297 1.544,0.632 1.844,0.8 0.299,0.168 10 I159 0.914,2.497 1.49,2.166 false
*a Component with harness connected
(Automatic Light Control Sensor)


for Manual Air Conditioning System

i.

Reconnect the I159 automatic light control sensor connector.


ii.

Connect an oscilloscope to the automatic light control sensor connector.


iii.
B113714E14
2.948,1.063 3.427,1.448 0.479,0.385 10 GND 1.844,1.177 2.438,1.604 0.594,0.427 10 A

Check the waveform.

OK:
Tester Connection Tool Setting Condition Specified Condition
I159-5 (CLTE) - I159-4 (CLTS) 5 V/DIV., 5 ms./DIV. Ignition switch ON, light control switch in AUTO position Correct waveform is as shown


HINT:

If the ambient light becomes brighter, width A becomes narrower.




Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR