Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM19V0EQ _59 Vehicle Exterior _014621 LIGHTING (EXT) _0074248 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Hazard Warning Switch Circuit  


DESCRIPTION

The combination meter assembly receives the hazard switch ON signal and controls the operation of the hazard warning lights.

WIRING DIAGRAM

E224262E02
1.546,0.83 1.64,0.981 0.095,0.15 10 6 1.722,0.83 2.048,0.981 0.326,0.15 10 GND 2.939,0.83 3.033,0.981 0.095,0.15 10 4 2.559,0.83 2.855,0.981 0.296,0.15 10 HAZ 4.826,0.83 4.92,0.981 0.095,0.15 10 5 5.002,0.914 5.298,1.065 0.296,0.15 10 HAZ 4.447,1.449 4.694,1.599 0.248,0.15 10 I17 4.447,1.617 6.285,1.767 1.838,0.15 10 Combination Meter Assembly 1.238,1.449 1.514,1.599 0.275,0.15 10 I56 1.238,1.617 3.364,1.961 2.126,0.345 10 Air Conditioning Control Assembly (Hazard Switch)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Read the display on the intelligent tester.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hazard Flasher Switch Hazard switch signal ON or OFF ON: Hazard switch on
OFF: Hazard switch off
-
Body Electrical > Combination Meter > Data List
Tester Display
Hazard Flasher Switch
50003 122 99
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT AIR CONDITIONING CONTROL ASSEMBLY (HAZARD SWITCH)
2.INSPECT AIR CONDITIONING CONTROL ASSEMBLY (HAZARD SWITCH)

b.
E216456C03
1.25,0.604 1.563,1.156 false 2.146,0.604 1.833,1.156 false 2.073,0.406 2.792,0.906 0.719,0.5 10 HAZ 0.969,0.406 1.781,0.792 0.813,0.385 10 GND 0.167,0.146 0.667,0.323 0.5,0.177 10 *a
*a Component without harness connected
(Air Conditioning Control Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (HAZ) - 6 (GND) Hazard switch on Below 1 Ω
4 (HAZ) - 6 (GND) Hazard switch off 10 kΩ or higher



Result:
Result Proceed to
OK A
NG (for Automatic air conditioning system) B
NG (for Manual air conditioning system) C



A

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - COMBINATION METER ASSEMBLY)

B

C

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I17 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I56-4 (HAZ) - I17-5 (HAZ) Always Below 1 Ω
I56-4 (HAZ) - Body ground Always 10 kΩ or higher
I56-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR