Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE(for Front Door)
RM19V0EQ _59 Vehicle Exterior _014623 EXTERIOR PANELS / TRIM _0074280 BLACK OUT TAPE(for Front Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Front Door)  INSTALLATION  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. REPAIR INSTRUCTION

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

NOTICE:

Do not heat the vehicle body excessively.



ii.

Wipe off any tape adhesive residue with cleaner.



b.

Installation temperature

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and comes off easily. When the temperature is high, the tape elasticity increases.





c.

Before installation

i.

Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.

NOTICE:

Do not bend the tape or leave it in high temperature places.




e.

Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)

NOTICE:
·

Position the tape accurately to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms and will not fit any more after being removed.



i.

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 30 to 70 mm (1.18 to 2.76 in.) per second.

B200106C14
0.063,0.083 3.375,1.583 3.313,1.5 2.219,0.229 2.156,0.229 2.156,0.229 2.01,0.688 false 1.396,1.146 1.396,1.333 false 0.844,0.563 0.688,0.688 false 1.833,3.552 1.979,3.552 false 5.417,3.469 5.563,3.469 false 1.594,3.052 1.75,3.188 false 4.833,3.073 5.229,3.146 false 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 2.25,0.115 2.563,0.344 0.313,0.229 10 false *1 1.313,1.344 1.604,1.563 0.292,0.219 10 false *2 0.865,0.406 1.125,0.656 0.26,0.25 10 false *3 0.25,1.75 0.75,2.083 0.5,0.333 12 false *A 3.917,1.75 4.375,2 0.458,0.25 12 false *B 2.042,1.813 2.365,2.042 0.323,0.229 10 false C 5.406,2.583 5.583,2.875 0.177,0.292 10 false D 1.656,3.448 1.969,3.656 0.313,0.208 10 false *5 5.25,3.365 5.469,3.594 0.219,0.229 10 false *5 1.438,2.917 1.74,3.135 0.302,0.219 10 false *4 1.115,2.323 1.427,2.573 0.313,0.25 10 false B 4.583,2.344 4.854,2.635 0.271,0.292 10 false B 2.813,2.573 3.042,2.792 0.229,0.219 10 false A 6.302,2.208 6.51,2.49 0.208,0.281 10 false A 4.656,2.958 4.906,3.229 0.25,0.271 10 false *4
*A Pressing Forward *B Pulling
*1 Non-padded Side *2 Padded Side
*3 Squeegee *4 Black Out Tape
*5 Release Paper - -
*a Side View - -


Reference Measurement
Area Measurement
A 10 to 20 mm (0.393 to 0.787 in.)
B 30 to 70 mm/sec. (1.18 to 2.76 in./sec.)
C 40 to 50° (for pressing forward)
D 30 to 45° (for pulling)

NOTICE:

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.


HINT:
·

Either angle of the squeegee (pressing forward or pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.394 to 0.787 in.) from the edge of the squeegee.





f.

Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)

i.
B147253C17
1.188,0.708 0.844,0.25 false 0.844,1 1.115,1.271 0.271,0.271 10 *c 1.396,0.521 1.656,0.771 0.26,0.25 10 *b 2.01,0.479 2.26,0.76 0.25,0.281 10 *a 0.677,0.094 0.938,0.344 0.26,0.25 10 *1 1.552,1.823 1.896,2.083 0.344,0.26 10 *2
*1 Squeegee
*2 Hem
*a First
*b Second
*c Third


If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.




g.

Key points for installation of the tape (how to use a squeegee and installation procedure for corners)

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.



h.

Check after installation

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.

NOTICE:

Do not reuse the tape.




Hide 75976G 3.INSTALL FRONT DOOR LOWER OUTSIDE STRIPE

a.

Refer to the illustration to position the front door lower outside stripe.

B280087C07
5.646,0.75 5.813,0.917 false 5.625,1.656 5.469,1.75 false 4.656,2.604 4.823,2.604 4.823,2.604 4.917,2.823 false 6.385,2.615 6.25,2.615 6.25,2.615 6.146,2.823 false 0.323,2.875 0.552,3.208 0.229,0.333 10 a 0.927,2.729 1.229,3.042 0.302,0.313 10 a 3.979,0.104 4.427,0.396 0.448,0.292 10 a-a 5.813,0.125 6.052,0.354 0.24,0.229 10 A 5.646,2.24 5.938,2.49 0.292,0.25 10 B 5.49,0.573 5.76,0.854 0.271,0.281 10 *a 5.292,1.698 5.542,1.917 0.25,0.219 10 *a 6.073,2.313 6.438,2.594 0.365,0.281 12 *B 4.854,2.323 5.188,2.604 0.333,0.281 12 *A 6.427,2.521 6.656,2.771 0.229,0.25 10 *c 4.49,2.49 4.708,2.729 0.219,0.24 10 *b
*A LH Side *B RH Side
*a Edge of Curved Surface *b Square
*c Round - -


Standard Measurement
Dimension Measurement
A 1.5 mm (0.0591 in.)
B 1.0 mm (0.0394 in.)


b.

Remove the release paper and apply the stripe.


Hide 75986B 4.INSTALL FRONT DOOR STRIPE

a.

Refer to the illustration to position a new front door stripe.

B280088C07
5.146,2.469 5.198,2.688 5.198,2.688 5.344,2.688 false 5.438,2.927 5.573,2.927 5.573,2.927 5.625,3.188 false 4.875,1.24 4.646,1.406 false 5.875,1.042 5.708,1.208 false 1.219,1.583 1.375,1.875 0.156,0.292 10 false a 1.073,2.177 1.229,2.469 0.156,0.292 10 false a 4.156,0.073 4.5,0.313 0.344,0.24 10 false a-a 4.052,0.885 4.26,1.094 0.208,0.208 10 false A 6.344,1.354 6.583,1.594 0.24,0.24 10 false B 4.49,1.344 4.771,1.604 0.281,0.26 10 false *a 5.896,0.896 6.156,1.146 0.26,0.25 10 false *a 3.875,2.813 4.167,3.063 0.292,0.25 12 false *B 3.865,1.875 4.188,2.156 0.323,0.281 12 false *A 5.365,2.594 5.615,2.823 0.25,0.229 10 false *b 5.292,2.823 5.563,3.073 0.271,0.25 10 false *c
*A LH Side *B RH Side
*a Edge of Curved Surface *b Square
*c Round - -


Standard Measurement
Dimension Measurement
A 1.5 mm (0.0591 in.)
B 1.0 mm (0.0394 in.)


b.

Remove the release paper and apply the stripe.


Hide 67664C 5.INSTALL DOOR FRAME GARNISH

Hide 67862 6.INSTALL FRONT DOOR WEATHERSTRIP

Hide 68620 7.INSTALL FRONT DOOR CHECK ASSEMBLY

Hide 68151C 8.INSTALL FRONT DOOR GLASS RUN

Hide 68102 9.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Hide 67832 10.INSTALL FRONT DOOR SERVICE HOLE COVER

Hide 11.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 13.INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)