Use the same procedure for both the RH and LH sides.
The procedure described below is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. REPAIR INSTRUCTION
75976G
3.INSTALL FRONT DOOR LOWER OUTSIDE STRIPE
75986B
4.INSTALL FRONT DOOR STRIPE
75754A
5.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING
75756C
6.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING
75720
7.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY
67481C
8.INSTALL DOOR DUST PROOF SEAL
Install door dust proof seal.
67001A
9.INSTALL FRONT DOOR PANEL CUSHION
Engage the 2 claws to install 2 new front door panel cushions.
67864B
10.INSTALL FRONT DOOR NO. 2 WEATHERSTRIP
Engage the 8 clips to install the front door No. 2 weatherstrip.
67664C
11.INSTALL DOOR FRAME GARNISH
Engage the clip to install a new door frame garnish.
67862
12.INSTALL FRONT DOOR WEATHERSTRIP
Engage the 19 clips and install the front door weatherstrip.
68620
13.INSTALL FRONT DOOR CHECK ASSEMBLY
Apply MP grease to the sliding areas of the front door check assembly.
Apply adhesive to the threads of the bolt (A).
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the front door check assembly with the 3 bolts.
69312
14.INSTALL FRONT DOOR LOCK OPEN ROD
Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.
82186B
15.INSTALL FRONT DOOR WIRE (w/ Smart Entry and Start System)
Engage the 3 clamps to install the front door wire.
69202A
16.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.
| *1 | Door Handle Nut |
| *a | Outside |
| *b | Inside |
Engage the claw.
Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw and door handle nut.
w/ Smart Entry and Start System:
Engage the 3 clamps.
Connect the connector.
69760C
17.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY
Install the front door inside locking cable assembly.
Engage the 3 claws.
69720B
18.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
Install the front door lock remote control cable assembly.
69040A
19.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY
When reusing the removed front door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.
Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock with motor assembly.
Apply MP grease to the sliding parts of the front door lock with motor assembly.
When reusing the front door lock with motor assembly:
Install a new door lock wiring harness seal to the front door lock with motor assembly.
| *1 | Front Door Lock Open Rod |
Insert the front door lock open rod to the front door lock with motor assembly.
Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.
Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.
69242E
20.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD
Engage the 2 claws to install the front door rear outside handle pad.
69241H
21.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD
Engage the 3 claws to install the front door front outside handle pad.
69220
22.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY
Insert the front end of the front door outside handle assembly into the front door outside handle frame.
Insert the rear end of the front door outside handle assembly into the front door outside handle frame, then slide the front door outside handle assembly toward the front of the vehicle to install it.
w/ Smart Entry and Start System:
Connect the connector.
Engage the 2 claws.
69217F
23.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)
Engage the 2 guides and claw, and install the front door outside handle cover to the lock cylinder assembly as shown in the illustration.
69250B
24.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
w/o Front Door Lock Cylinder:
Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.
Install the hole plug.
w/ Front Door Lock Cylinder:
Use the same procedures for the front passenger side and the driver side.
25.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)
Using a T30 "TORX" socket wrench, install the front door outside handle cover with lock cylinder assembly with the screw.
Install the hole plug.
26.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Front Passenger Side)
w/ Front Door Lock Cylinder:
Use the same procedures for the front passenger side and the driver side.
67404F
27.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Engage the guide as shown in the illustration.
Install the front door rear lower frame sub-assembly with the 2 bolts.
67402F
28.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Engage the guide as shown in the illustration.
Install the front door front lower frame sub-assembly with the 2 bolts.
68151C
29.INSTALL FRONT DOOR GLASS RUN
Install the front door glass run.
67924
30.INSTALL NO. 2 FRONT DOOR STIFFENER CUSHION
Clean the front door panel sub-assembly.
| *1 | Double-sided Tape |
Engage the 2 guides.
Install a new No. 2 front door stiffener cushion with the 2 bolts.
85720D
31.INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
The regulator arm must be below the intermediate position when installing the power window regulator motor.
Using a T25 "TORX" socket wrench, install the front power window regulator motor assembly with the 3 screws.
A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
32.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY
Apply MP grease to the sliding parts of the front door window regulator assembly.
Install the temporary bolt to the front door window regulator assembly.
| *1 | Temporary Bolt |
Temporarily install the front door window regulator assembly.
Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.
Tighten the bolts in the order shown in the illustration.
68102
33.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
Connect the cable to the negative (-) battery terminal.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Disconnect the power window regulator master switch assembly.
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.
Install the front door glass sub-assembly with the 2 bolts.
Install the grommet.
67832
34.INSTALL FRONT DOOR SERVICE HOLE COVER
Apply new butyl tape to the front door panel.
| *1 | Reference Point |
Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
Attach the front door service hole cover according to the reference points on the front door panel.
Securely install the front door service hole cover preventing wrinkles and air bubbles.
Engage the 3 clamps.
Connect each connector.
89430
35.INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)
Use the same procedure for the RH side and LH side.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>INSTALLATION
36.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY
86160
37.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
84927
38.INSTALL SEAT MEMORY SWITCH (w/ Memory)
68172A
39.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP
Install the front door inner glass weatherstrip.
69206B
40.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the 2 claws and guide, and install the front door inside handle sub-assembly to the front door trim board sub-assembly.
67602
41.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
Connect the front door lock remote control cable assembly and front door inside locking cable assembly.
| *1 | Reference Boss |
Engage the front door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
Engage the 10 clips and install to front door trim board sub-assembly.
Install the 3 screws.
If protective tape has been applied, remove it.
81911B
42.INSTALL FRONT REFLEX REFLECTOR ASSEMBLY
Connect the connector.
| *A | for LH Side |
| *B | for RH Side |
Engage the claw to install the front reflex reflector assembly.
74220
43.INSTALL FRONT ARMREST ASSEMBLY
Engage the 2 guides, 3 clips and 7 claws, and install the front armrest assembly.
44.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
Connect each connector.
Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator master switch assembly with front door armrest base panel.
45.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
Connect the connector.
Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.
67492A
46.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH
Engage the 3 clips to install the front door lower frame bracket garnish.
69284C
47.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG
Engage the 3 claws to install the front door inside handle bezel plug.
48.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
49.INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)
50.INSPECT POWER WINDOW OPERATION