Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › 2011.10–2016.05
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM J

2AR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the No. 1 integration relay (EFI MAIN relay), closing the contacts and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A266855E05
5.49,1.958 5.771,2.104 0.281,0.146 10 false A25 5.49,4.25 5.781,4.396 0.292,0.146 10 false E26 5.531,1.771 5.719,1.927 0.188,0.156 10 false 37 5.573,2.188 5.688,2.344 0.115,0.156 10 false 3 5.531,4.083 5.708,4.24 0.177,0.156 10 false 16 5.844,1.854 6.281,2 0.438,0.146 10 false IGSW 5.844,2.375 6.135,2.542 0.292,0.167 10 false +B2 5.844,2.833 6.135,3 0.292,0.167 10 false +B 5.844,3.719 6.281,3.865 0.438,0.146 10 false MREL 5.844,4.25 6.135,4.417 0.292,0.167 10 false E1 5.563,0.833 5.854,0.979 0.292,0.146 10 false A43 5.656,0.354 5.76,0.521 0.104,0.167 10 false 9 3.531,2.094 4.115,2.406 0.583,0.313 10 false ECU-IG2 NO. 3 2.792,2.625 3.042,2.792 0.25,0.167 10 false IG2 3.26,3.427 3.906,3.594 0.646,0.167 10 false EFI NO. 2 2.583,4.021 3.208,4.188 0.625,0.167 10 false EFI MAIN 4.313,2.823 4.542,2.99 0.229,0.167 10 false 1C 3.406,1.656 3.635,1.823 0.229,0.167 10 false 1C 4.313,1.958 4.542,2.125 0.229,0.167 10 false 1C 4.302,3.292 4.531,3.458 0.229,0.167 10 false 1C 4.313,3.729 4.542,3.896 0.229,0.167 10 false 1C 1.802,1.958 2.031,2.125 0.229,0.167 10 false 1D 1.802,3.719 2.031,3.885 0.229,0.167 10 false 1E 1.854,1.75 1.958,1.917 0.104,0.167 10 false 3 1.031,0.333 1.135,0.5 0.104,0.167 10 false 5 2.333,0.333 2.438,0.5 0.104,0.167 10 false 6 4.365,1.771 4.469,1.938 0.104,0.167 10 false 1 4.375,3.531 4.479,3.698 0.104,0.167 10 false 7 4.313,2.635 4.49,2.802 0.177,0.167 10 false 10 1.854,3.531 1.958,3.698 0.104,0.167 10 false 2 1.802,3.281 2.031,3.448 0.229,0.167 10 false 1B 1.854,3.094 1.958,3.26 0.104,0.167 10 false 1 4.365,3.104 4.469,3.271 0.104,0.167 10 false 9 3.365,1.448 3.469,1.615 0.104,0.167 10 false 8 0.677,2.104 1.313,2.271 0.635,0.167 10 false IG2-MAIN 0.354,1.156 0.885,1.302 0.531,0.146 10 false ST/AM2 1.219,0.542 1.531,0.688 0.313,0.146 10 false AM2 2.365,4.479 3.854,4.719 1.49,0.24 10 false No. 1 Integration Relay 5.563,0.99 7.125,1.302 1.563,0.313 10 false Certification ECU (Smart Key ECU Assembly)*2 0.51,4.76 0.99,4.948 0.479,0.188 10 false Battery 0.406,4.042 1,4.229 0.594,0.188 10 false FL MAIN 6.188,4.656 6.542,4.813 0.354,0.156 10 false ECM 5.844,0.427 6.219,0.573 0.375,0.146 10 false IG2D 5.49,2.365 5.771,2.51 0.281,0.146 10 false A25 5.573,2.656 5.688,2.813 0.115,0.156 10 false 2 5.49,2.833 5.771,2.979 0.281,0.146 10 false A25 5.531,3.542 5.708,3.698 0.177,0.156 10 false 46 5.49,3.719 5.771,3.865 0.281,0.146 10 false A25 1.948,0.542 2.208,0.698 0.26,0.156 10 false IG2 2.5,0.583 3.479,0.74 0.979,0.156 10 false ECU-IG2 NO. 1 0.958,0.781 1.177,0.938 0.219,0.156 10 false I36 0.958,0.927 3.281,1.313 2.323,0.385 10 false Ignition or Starter Switch Assembly*1 3.479,4.958 5.813,5.135 2.333,0.177 10 false *1: w/o Smart Entry and Start System 3.479,5.302 5.74,5.479 2.26,0.177 10 false *2: w/ Smart Entry and Start System 0.667,3.458 1.313,3.781 0.646,0.323 10 false EFI-MAIN NO. 1 0.646,0.323 0.865,0.479 0.219,0.156 10 false *1 2.573,0.323 2.792,0.479 0.219,0.156 10 false *1 3.656,0.323 3.875,0.479 0.219,0.156 10 false *1 4.927,0.323 5.146,0.479 0.219,0.156 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY VOLTAGE)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1C-8 - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG (w/o smart entry and start system) B
NG (w/ smart entry and start system) C



A

2.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)

B

7.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

C

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)
2.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1D-3 - Body ground Always 11 to 14 V
1B-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN AND IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN AND IG2 RELAY)
a.

Inspect the No. 1 integration relay (EFI MAIN and IG2 relay).

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - A25-37 (IGSW) Always Below 1 Ω
1C-9 - A25-2 (+B) Always Below 1 Ω
1C-10 - A25-3 (+B2) Always Below 1 Ω
1C-7 - A25-46 (MREL) Always Below 1 Ω
1C-1 or A25-37 (IGSW) - Body ground Always 10 kΩ or higher
1C-9 or A25-2 (+B) - Body ground Always 10 kΩ or higher
1C-10 or A25-3 (+B2) - Body ground Always 10 kΩ or higher
1C-7 or A25-46 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-16 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I36-5 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-9 (IG2D) - 1C-8 Always Below 1 Ω
A43-9 (IG2D) or 1C-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR