Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › 2011.10–2015.04
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM J

2AR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the ignition switch is turned to ON, the MIL should be illuminated and should turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A266858E03
0.66,0.53 0.755,0.683 0.095,0.153 10 5 0.842,0.53 1.148,0.683 0.306,0.153 10 AM2 1.926,0.525 2.022,0.678 0.095,0.153 10 6 1.595,0.525 1.838,0.678 0.243,0.153 10 IG2 0.571,1.005 0.833,1.158 0.262,0.153 10 I36 0.571,1.173 2.899,1.326 2.328,0.153 10 Ignition or Starter Switch Assembly*1 0.567,1.679 1.088,1.832 0.521,0.153 10 ST/AM2 0.854,2.415 1.537,2.562 0.682,0.148 10 IG2-MAIN 0.616,3.493 1.298,3.641 0.682,0.148 10 FL MAIN 0.74,4.577 1.202,4.73 0.462,0.153 10 Battery 2.222,3.437 3.696,3.59 1.474,0.153 10 No. 1 Integration Relay 2.418,4.838 4.764,4.991 2.345,0.153 10 *1: w/o Smart Entry and Start System 2.418,5.189 4.694,5.341 2.276,0.153 10 *2: w/ Smart Entry and Start System 2.429,3.105 2.672,3.257 0.243,0.153 10 IG2 1.945,2.285 2.145,2.438 0.2,0.153 10 1D 1.987,2.112 2.083,2.264 0.095,0.153 10 3 1.945,2.775 2.145,2.928 0.2,0.153 10 1E 1.987,2.602 2.083,2.755 0.095,0.153 10 2 3.763,2.294 3.963,2.447 0.2,0.153 10 1C 3.805,2.12 3.901,2.273 0.095,0.153 10 5 2.945,1.83 3.145,1.982 0.2,0.153 10 1C 3.077,2.007 3.172,2.159 0.095,0.153 10 8 4.273,2.416 5.049,2.569 0.776,0.153 10 METER-IG2 5.408,2.43 6.21,2.583 0.802,0.153 10 CHECK E/G 5.029,2.206 5.222,2.359 0.193,0.153 10 13 5.31,2.206 5.568,2.359 0.259,0.153 10 IG+ 6.402,2.206 6.585,2.359 0.182,0.153 10 22 5.996,2.206 6.314,2.359 0.318,0.153 10 CHK 4.688,2.772 4.96,2.925 0.273,0.153 10 I18 4.688,2.94 6.52,3.093 1.832,0.153 10 Combination Meter Assembly 5.586,1.18 5.859,1.333 0.273,0.153 10 A43 5.586,1.348 7.136,1.662 1.55,0.314 10 Certification ECU (Smart Key ECU Assembly)*2 5.767,0.523 5.862,0.676 0.095,0.153 10 9 5.949,0.607 6.294,0.76 0.345,0.153 10 IG2D 2.024,0.742 3.009,0.898 0.984,0.156 10 ECU-IG2 NO. 1 5.688,3.964 5.866,4.117 0.177,0.153 10 30 5.949,3.964 6.102,4.117 0.153,0.153 10 W 6.315,4.979 6.641,5.131 0.326,0.153 10 ECM 5.965,4.979 6.239,5.131 0.274,0.153 10 A25 0.539,0.73 0.708,0.883 0.169,0.153 10 *1 2.192,0.53 2.361,0.683 0.169,0.153 10 *1 2.809,0.53 2.977,0.683 0.169,0.153 10 *1 4.546,0.53 4.715,0.683 0.169,0.153 10 *2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.


Result:
Result Proceed to
MIL remains ON A
MIL does not illuminate B



A

2.CHECK WHETHER DTC OUTPUT RECURS

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Check if any DTCs have been detected. Note down any DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC is not output A
Any DTCs is output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.



A

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
A255690C27
0.583,0.969 0.99,1.25 0.406,0.281 0.708,0.042 1.052,0.302 0.344,0.26 10 *a 0.667,1.031 1.073,1.313 0.406,0.281 10 A25
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-22 (CHK) or A25-30 (W) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL should be illuminated.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Start the engine.


Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The intelligent tester cannot communicate with the ECM.



A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-22 (CHK) - A25-30 (W) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR