Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › 2011.10–2016.05
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM J

2AR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A256646E11
1.333,0.844 2.646,1.135 1.313,0.292 10 false from EFI NO. 1 Fuse 1.333,1.208 2.646,1.51 1.313,0.302 10 false from EFI NO. 2 Fuse 0.135,1.781 2.625,2.281 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.688 2.635,3.052 2.5,0.365 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.104 5.313,3.417 0.344,0.313 10 false ECM 2.885,0.75 3.271,0.896 0.385,0.146 10 false BATT 2.823,1.094 3.365,1.24 0.542,0.146 10 false +B, +B2 3.115,2.021 3.396,2.208 0.281,0.188 10 false VC 4.396,0.844 6.188,1.198 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.792 6.354,2.146 0.99,0.354 10 false Microprocessor 4.073,2.844 4.219,3.01 0.146,0.167 10 false R

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated when the ignition switch is turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A262634E14
0.25,0.76 0.521,0.917 0.271,0.156 10 false E55 0.25,0.917 1.917,1.271 1.667,0.354 10 false Camshaft Position Sensor (for Intake Camshaft) 2.885,0.688 3.01,0.865 0.125,0.177 10 false 3 2.885,1.094 3.01,1.271 0.125,0.177 10 false 1 2.896,1.51 3.021,1.688 0.125,0.177 10 false 2 2.583,0.781 2.813,0.948 0.229,0.167 10 false VC 2.448,1.188 2.844,1.344 0.396,0.156 10 false VV1+ 2.458,1.615 2.813,1.771 0.354,0.156 10 false VV1- 0.25,2.281 0.531,2.438 0.281,0.156 10 false E52 0.25,2.448 1.948,2.792 1.698,0.344 10 false Camshaft Position Sensor (for Exhaust Camshaft) 2.896,2.208 3.021,2.385 0.125,0.177 10 false 3 2.896,2.615 3.021,2.792 0.125,0.177 10 false 1 2.896,3.042 3.021,3.219 0.125,0.177 10 false 2 2.5,2.302 2.813,2.469 0.313,0.167 10 false VC2 2.438,2.719 2.833,2.875 0.396,0.156 10 false VVE+ 2.448,3.146 2.802,3.302 0.354,0.156 10 false VVE- 5.313,0.635 5.75,0.958 0.438,0.323 10 false 113 5.302,0.781 5.688,0.99 0.385,0.208 10 false E26 5.313,1.198 5.583,1.354 0.271,0.156 10 false E26 5.313,1.615 5.656,1.813 0.344,0.198 10 false E26 5.313,2.292 5.688,2.583 0.375,0.292 10 false E26 5.313,2.708 5.583,2.865 0.271,0.156 10 false E26 5.313,3.125 5.583,3.281 0.271,0.156 10 false E26 5.656,0.688 6.177,1.052 0.521,0.365 10 false VCV1 5.365,1.052 5.563,1.208 0.198,0.156 10 false 82 5.656,1.198 6.219,1.563 0.563,0.365 10 false VV1+ 5.313,1.469 5.667,1.677 0.354,0.208 10 false 114 5.656,1.521 6.094,1.792 0.438,0.271 10 false VV1- 5.313,2.156 5.688,2.375 0.375,0.219 10 false 111 5.646,2.208 6.125,2.49 0.479,0.281 10 false VCE1 5.354,2.552 5.583,2.729 0.229,0.177 10 false 81 5.646,2.719 6.125,3.042 0.479,0.323 10 false EV1+ 5.313,2.99 5.708,3.219 0.396,0.229 10 false 112 5.646,3.042 6.115,3.333 0.469,0.292 10 false EV1- 6.042,7.948 6.385,8.104 0.344,0.156 10 false ECM 5.313,3.76 5.656,3.979 0.344,0.219 10 false 125 5.646,3.813 6.188,4.271 0.542,0.458 10 false VCTA 5.313,3.906 5.594,4.052 0.281,0.146 10 false E26 5.313,4.125 5.656,4.323 0.344,0.198 10 false 127 5.313,4.271 5.594,4.417 0.281,0.146 10 false E26 5.313,4.5 5.615,4.677 0.302,0.177 10 false 128 5.313,4.635 5.688,4.854 0.375,0.219 10 false E26 5.302,5 5.635,5.198 0.333,0.198 10 false E26 5.313,4.865 5.635,5.063 0.323,0.198 10 false 126 5.646,4.281 6.031,4.427 0.385,0.146 10 false VTA1 5.646,4.646 6.031,4.792 0.385,0.146 10 false VTA2 5.646,4.906 6.031,5.094 0.385,0.188 10 false ETA 5.354,5.438 5.615,5.604 0.26,0.167 10 false 53 5.302,5.583 5.656,5.781 0.354,0.198 10 false A25 5.313,5.938 5.656,6.146 0.344,0.208 10 false A25 5.302,6.302 5.698,6.552 0.396,0.25 10 false A25 5.313,6.698 5.677,6.917 0.365,0.219 10 false A25 5.313,7.063 5.667,7.25 0.354,0.188 10 false A25 5.313,7.427 5.677,7.646 0.365,0.219 10 false A25 5.354,5.802 5.594,5.969 0.24,0.167 10 false 56 5.354,6.167 5.635,6.375 0.281,0.208 10 false 51 5.354,6.563 5.615,6.76 0.26,0.198 10 false 54 5.365,6.927 5.646,7.115 0.281,0.188 10 false 52 5.365,7.292 5.552,7.438 0.188,0.146 10 false 55 5.635,5.49 6.125,5.708 0.49,0.219 10 false VCPA 5.635,6.323 5.948,6.479 0.313,0.156 10 false VPA 5.635,6.969 5.979,7.156 0.344,0.188 10 false EPA 5.635,6.708 6.01,6.865 0.375,0.156 10 false VPA2 5.635,7.333 6.094,7.552 0.458,0.219 10 false EPA2 5.635,5.854 6.083,6.063 0.448,0.208 10 false VCP2 0.24,4.01 0.521,4.167 0.281,0.156 10 false E16 0.24,4.177 1.479,4.542 1.24,0.365 10 false Throttle with Motor Body Assembly 2.594,3.927 2.833,4.083 0.24,0.156 10 false VC 2.521,4.292 2.833,4.448 0.313,0.156 10 false VTA 2.448,4.646 2.823,4.813 0.375,0.167 10 false VTA2 2.625,5.01 2.844,5.177 0.219,0.167 10 false E2 2.885,3.813 3.083,4.083 0.198,0.271 10 false 5 2.885,4.177 3.083,4.417 0.198,0.24 10 false 6 2.885,4.542 3.083,4.75 0.198,0.208 10 false 4 2.885,4.917 3.167,5.156 0.281,0.24 10 false 3 0.229,5.698 0.635,5.854 0.406,0.156 10 false A36 0.229,5.865 1.833,6.198 1.604,0.333 10 false Accelerator Pedal Sensor Assembly 2.417,5.604 2.833,5.75 0.417,0.146 10 false VCPA 2.417,5.979 2.833,6.125 0.417,0.146 10 false VCP2 2.51,6.344 2.833,6.49 0.323,0.146 10 false VPA 2.438,6.719 2.854,6.865 0.417,0.146 10 false VPA2 2.51,7.083 2.833,7.229 0.323,0.146 10 false EPA 2.438,7.417 2.885,7.615 0.448,0.198 10 false EPA2 2.885,5.49 3.156,5.729 0.271,0.24 10 false 4 2.885,5.854 3.073,6.063 0.188,0.208 10 false 1 2.885,6.219 3.156,6.479 0.271,0.26 10 false 6 2.885,6.615 3.073,6.813 0.188,0.198 10 false 3 2.885,6.969 3.073,7.219 0.188,0.25 10 false 5 2.896,7.333 3.167,7.615 0.271,0.281 10 false 2

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Check the communication between the tester and ECM.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle with motor body assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B


HINT:

Perform "Inspection After Repair" after replacing the throttle with motor body assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



A

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)

B

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

5.CHECK MIL (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT)

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK MIL (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT)
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

6.CHECK MIL (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

6.CHECK MIL (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

7.CHECK HARNESS AND CONNECTOR

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

7.CHECK HARNESS AND CONNECTOR
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Disconnect the camshaft position sensor (for intake camshaft) connector.


c.

Disconnect the throttle with motor body assembly connector.


d.

Disconnect the accelerator pedal sensor assembly connector.


e.

Disconnect the ECM connectors.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-111 (VCE1) - Body ground Always 10 kΩ or higher
E26-113 (VCV1) - Body ground Always 10 kΩ or higher
E26-125 (VCTA) - Body ground Always 10 kΩ or higher
A25-53 (VCPA) - Body ground Always 10 kΩ or higher
A25-56 (VCP2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR