Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074095 PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the navigation ECU sub-assembly judges that the signals or signal lines between the navigation ECU sub-assembly and the rear television camera assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Navigation ECU sub-assembly



WIRING DIAGRAM

E226207E26
0.135,2.76 2.208,3.115 2.073,0.354 10 false Navigation ECU Sub-assembly 5.396,0.656 5.573,0.823 0.177,0.167 10 false 3 5.396,1.188 5.573,1.354 0.177,0.167 10 false 2 5.396,0.125 5.573,0.292 0.177,0.167 10 false 6 5.396,1.719 5.573,1.885 0.177,0.167 10 false 5 5.615,0.729 6.031,0.896 0.417,0.167 10 false CV+ 5.615,1.271 6.031,1.438 0.417,0.167 10 false CV- 5.615,0.198 6.031,0.365 0.417,0.167 10 false CB+ 5.615,1.813 6.083,1.979 0.469,0.167 10 false CGND 2.021,1.083 2.219,1.25 0.198,0.167 10 false 16 2.021,1.615 2.219,1.781 0.198,0.167 10 false 15 2.063,2.146 2.26,2.313 0.198,0.167 10 false 7 1.594,0.74 2.01,0.906 0.417,0.167 10 false V+ 1.604,1.271 2.021,1.438 0.417,0.167 10 false V- 1.521,0.198 1.938,0.365 0.417,0.167 10 false CA+ 1.385,1.813 1.854,1.979 0.469,0.167 10 false CGND 1.385,2.344 1.854,2.51 0.469,0.167 10 false GND1 5.469,2.938 6.906,3.354 1.438,0.417 10 false Rear Television Camera Assembly 3.438,3.125 4.344,3.333 0.906,0.208 10 false *1: Shielded 4.521,1.938 4.771,2.135 0.25,0.198 10 false *1 3.833,1.938 4.083,2.135 0.25,0.198 10 false *1 3.135,1.948 3.385,2.146 0.25,0.198 10 false *1 2.063,0.552 2.24,0.719 0.177,0.167 10 false 8 2.063,0.031 2.24,0.198 0.177,0.167 10 false 7 5.469,2.76 5.667,2.927 0.198,0.167 10 false T6 2,0.74 2.26,0.906 0.26,0.167 10 false I66 2.01,1.271 2.271,1.438 0.26,0.167 10 false I66 2.01,0.208 2.271,0.375 0.26,0.167 10 false I66 2.01,1.802 2.24,1.969 0.229,0.167 10 false I66 2.01,2.333 2.26,2.5 0.25,0.167 10 false I64

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the navigation ECU sub-assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the I66 connector from the navigation ECU sub-assembly.


b.

Disconnect the T6 connector from the rear television camera assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I66-16 (V-) - T6-2 (CV-) Always Below 1 Ω
I66-8 (V+) - T6-3 (CV+) Always Below 1 Ω
I66-15 (CGND) - T6-5 (CGND) Always Below 1 Ω
I66-7 (CA+) - T6-6 (CB+) Always Below 1 Ω
I66-16 (V-) - Body ground Always 10 kΩ or higher
I66-8 (V+) - Body ground Always 10 kΩ or higher
I66-15 (CGND) - Body ground Always 10 kΩ or higher
I66-7 (CA+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT NAVIGATION ECU SUB-ASSEMBLY (V-, CGND, CA+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NAVIGATION ECU SUB-ASSEMBLY (V-, CGND, CA+)
a.
E216447C11
1.448,0.323 1.938,0.615 0.49,0.292 1.385,1.781 1.073,2.448 1.073,2.448 0.74,2.448 false 1.24,1.781 0.719,1.781 false 1.375,1.635 1.073,0.885 1.073,0.885 0.74,0.885 false 0.469,1.698 0.802,1.875 0.333,0.177 10 V- 0.198,2.375 0.635,2.552 0.438,0.177 10 CGND 0.167,0.104 0.604,0.281 0.438,0.177 10 *a 1.563,0.375 1.781,0.552 0.219,0.177 10 I66 0.365,0.802 0.698,0.979 0.333,0.177 10 CA+
*a Component with harness connected
(Navigation ECU Sub-assembly)


Reconnect the I66 connector to the navigation ECU sub-assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I66-16 (V-) - Body ground Always Below 1 Ω
I66-15 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I66-7 (CA+) - I66-15 (CGND) Engine switch on (IG)
Shift lever in R
5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION ECU SUB-ASSEMBLY (V+, GND1)

NG

3.INSPECT NAVIGATION ECU SUB-ASSEMBLY (V+, GND1)
a.

Reconnect the T6 connector to the rear television camera assembly.


b.
E265837C01
1.521,0.167 1.948,0.448 0.427,0.281 1.167,2.604 1.594,2.885 0.427,0.281 0.698,0.802 1.365,0.802 1.365,0.802 1.365,0.969 false 0.781,4.042 1.25,4.042 1.25,4.042 1.448,3.604 false 1.646,0.208 2.104,0.406 0.458,0.198 10 I66 0.302,0.177 0.76,0.375 0.458,0.198 10 *a 1.292,2.646 1.75,2.844 0.458,0.198 10 I64 0.396,3.958 0.854,4.156 0.458,0.198 10 GND1 0.479,0.719 0.938,0.917 0.458,0.198 10 V+
*a Component with harness connected
(Navigation ECU Sub-assembly)


E265838C01
0.896,2.281 1.094,2.281 1.094,2.281 1.219,1.708 false 0.979,4.417 1.125,4.417 1.125,4.417 1.24,3.844 false 1.698,2.292 1.417,2.292 1.417,2.292 1.323,1.615 false 1.698,4.396 1.469,4.396 1.469,4.396 1.354,3.781 false 0.281,0.458 0.594,0.656 0.313,0.198 10 *a 0.271,2.427 0.583,2.625 0.313,0.198 10 *b 0.74,2.188 1.052,2.385 0.313,0.198 10 *c 1.771,2.208 2.083,2.406 0.313,0.198 10 *d 0.813,4.323 1.125,4.521 0.313,0.198 10 *c 1.719,4.323 2.031,4.521 0.313,0.198 10 *d 0.438,3.458 0.906,3.771 0.469,0.313 10 GND 0.396,1.104 0.865,1.417 0.469,0.313 10 GND
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reconnect the I66 connector to the navigation ECU sub-assembly.


c.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation ECU sub-assembly with the connector connected.


OK:

Waveform is as shown in the illustration.


Item Content
Terminal No. (Symbol) I66-8 (V+) - I64-7 (GND1)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG), shift lever in R

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



Result:
Proceed to
OK
NG



OK

NG

REPLACE REAR TELEVISION CAMERA ASSEMBLY