Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074094 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Main Switch Circuit  


DESCRIPTION

When the blind spot monitor main switch (warning canceling switch assembly) is turned on, a signal is sent to the blind spot monitor sensor RH. The blind spot monitor system operates according to this signal.

WIRING DIAGRAM

E224414E11
5.438,0.646 5.885,0.813 0.448,0.167 10 false BSSW 5.281,0.521 5.385,0.698 0.104,0.177 10 false 3 4.49,0.531 4.594,0.708 0.104,0.177 10 false 8 4.313,0.729 4.458,0.906 0.146,0.177 10 false D 3.521,0.729 3.667,0.906 0.146,0.177 10 false B 3.313,0.531 3.5,0.708 0.188,0.177 10 false 11 5.313,1.958 5.74,2.104 0.427,0.146 10 false O28 5.313,2.125 7.031,2.469 1.719,0.344 10 false Blind Spot Monitor Sensor RH 2.115,0.781 3.125,0.938 1.01,0.156 10 false ECU-IG1 NO. 3 0.208,0.625 1.927,0.875 1.719,0.25 10 false from IG1 NO. 2 Relay 3.323,1 3.865,1.198 0.542,0.198 10 false I157 3.313,1.167 5.24,1.885 1.927,0.719 10 false Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Blind Spot Monitor Master / Data list.


e.

According to the display on intelligent tester, read the Data List.

Body Electrical > Blind Spot Monitor Master > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch Blind spot monitor main switch (warning canceling switch assembly) OFF or ON ON: Blind spot monitor main switch (warning canceling switch assembly) on
OFF: Blind spot monitor main switch (warning canceling switch assembly) off
-
Body Electrical > Blind Spot Monitor Master > Data List
Tester Display
Main Switch
50003 313 2

Result:
Result Proceed to
The display does not change as shown above when the blind spot monitor main switch (warning canceling switch assembly) is operated. A
The display changes as shown above when the blind spot monitor main switch (warning canceling switch assembly) is operated. B



A

2.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)
a.

Remove the blind spot monitor main switch (warning canceling switch assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH>REMOVAL


b.
E224422C22
1.5,0.333 1.958,0.615 0.458,0.281 1.979,1.375 2.542,0.625 false 1.5,1.458 1.854,1.948 1.854,1.948 1.958,1.948 false 2.573,0.521 2.75,0.698 0.177,0.177 10 false D 2.01,1.854 2.302,2.031 0.292,0.177 10 false B 0.167,0.146 0.521,0.396 0.354,0.25 10 false *a 1.615,0.385 2.083,0.74 0.469,0.354 10 false I157
*a Component without harness connected
(Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I157-11 (B) - I157-8 (D) Blind spot monitor main switch assembly is on (not protruding) Below 1 Ω
I157-11 (B) - I157-8 (D) Blind spot monitor main switch assembly is off (protruding) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)

NG

REPLACE BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I157-11 (B) - Body ground Engine switch on (IG) 11 to 14 V
I157-11 (B) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR RH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O28-3 (BSSW) - I157-8 (D) Always Below 1 Ω
O28-3 (BSSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR