Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM19V0EQ _58 Vehicle Interior _014605 DOOR LOCK _0074105 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the door control switch (power window regulator master switch assembly), and driver door key cylinder or front passenger door key cylinder* switch signals from the front door lock with motor assembly (driver door) or front door lock with motor assembly (front passenger door)*. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

*: w/o wireless door lock control function


WIRING DIAGRAM

B279064
5.471,5.928 7.118,6.246 1.647,0.318 10 Main Body ECU (Multiplex Network Body ECU) 0.766,1.769 3.633,2.08 2.867,0.311 10 Door Key Lock and Unlock Switch (Front Door Lock with Motor Assembly (Driver Door)) 0.766,5.365 3.04,5.688 2.274,0.323 10 Door Control Switch (Power Window Regulator Master Switch Assembly) 0.766,3.52 3.971,3.831 3.205,0.311 10 Door Key Lock and Unlock Switch (Front Door Lock with Motor Assembly (Front Passenger Door))*1 0.273,6.329 3.096,6.495 2.823,0.166 10 *1: w/o Wireless Door Lock Control Function 3.468,3.079 3.624,3.244 0.156,0.166 10 *1 0.82,2.784 0.976,2.95 0.156,0.166 10 *1 3.468,2.518 3.624,2.684 0.156,0.166 10 *1 1.259,2.81 1.362,2.95 0.103,0.14 10 8 2.219,2.527 2.322,2.667 0.103,0.14 10 5 2.219,3.073 2.329,3.213 0.11,0.14 10 6 1.259,1.031 1.362,1.171 0.103,0.14 10 7 2.219,1.294 2.397,1.434 0.177,0.14 10 10 2.219,0.747 2.329,0.887 0.11,0.14 10 9 1.259,4.54 1.362,4.681 0.103,0.14 10 1 2.219,4.257 2.326,4.397 0.106,0.14 10 9 2.219,4.803 2.329,4.943 0.11,0.14 10 2 5.73,2.419 5.907,2.559 0.177,0.14 10 12 5.73,0.612 5.907,0.752 0.177,0.14 10 11 5.73,1.186 5.907,1.326 0.177,0.14 10 24 5.765,4.71 5.872,4.85 0.106,0.14 10 9 5.721,4.149 5.915,4.289 0.193,0.14 10 10 1.943,4.207 2.159,4.349 0.216,0.142 10 UL 2.027,4.991 2.137,5.134 0.11,0.142 10 L 1.415,4.543 1.534,4.685 0.119,0.142 10 E 1.966,1.475 2.173,1.617 0.207,0.142 10 UL 2.046,0.685 2.163,0.828 0.117,0.142 10 L 1.424,1.026 1.544,1.169 0.119,0.142 10 E 1.952,2.469 2.169,2.612 0.216,0.142 10 UL 2.046,3.263 2.155,3.406 0.11,0.142 10 L 1.424,2.806 1.544,2.948 0.119,0.142 10 E 6.031,0.836 6.208,0.976 0.177,0.14 10 L2 6.031,1.396 6.305,1.536 0.274,0.14 10 UL3 6.031,2.622 6.305,2.762 0.274,0.14 10 UL2 6.031,4.913 6.208,5.053 0.177,0.14 10 L1 6.031,4.353 6.305,4.493 0.274,0.14 10 UL1 5.71,4.904 5.925,5.044 0.215,0.14 10 I13 5.71,4.343 5.925,4.483 0.215,0.14 10 I13 5.71,2.62 5.925,2.76 0.215,0.14 10 I13 5.71,1.387 5.925,1.527 0.215,0.14 10 I13 5.71,0.827 5.925,0.967 0.215,0.14 10 I13 0.772,5.191 1.051,5.331 0.279,0.14 10 K10 0.772,3.327 0.94,3.467 0.168,0.14 10 J1 0.766,1.562 0.961,1.702 0.196,0.14 10 K1 0.082,0.038 0.743,0.211 0.661,0.172 12 for LHD:

B294404
5.477,4.978 7.124,5.297 1.647,0.318 10 Main Body ECU (Multiplex Network Body ECU) 0.772,2.08 3.643,2.392 2.872,0.311 10 Door Key Lock and Unlock Switch (Front Door Lock with Motor Assembly (Driver Door)) 0.772,4.416 3.046,4.738 2.274,0.323 10 Door Control Switch (Power Window Regulator Master Switch Assembly) 1.265,1.343 1.368,1.483 0.103,0.14 10 8 2.225,1.605 2.338,1.745 0.112,0.14 10 5 2.225,1.059 2.335,1.199 0.11,0.14 10 6 1.265,3.591 1.368,3.731 0.103,0.14 10 9 2.225,3.308 2.332,3.448 0.106,0.14 10 8 2.225,3.854 2.335,3.994 0.11,0.14 10 2 5.736,0.923 5.913,1.064 0.177,0.14 10 11 5.736,1.498 5.913,1.638 0.177,0.14 10 24 5.771,3.761 5.878,3.901 0.106,0.14 10 9 5.728,3.2 5.921,3.34 0.193,0.14 10 10 1.949,3.257 2.165,3.4 0.216,0.142 10 UL 2.033,4.042 2.152,4.184 0.119,0.142 10 L 1.421,3.594 1.54,3.736 0.119,0.142 10 E 1.958,1.786 2.175,1.929 0.216,0.142 10 UL 2.052,0.997 2.171,1.139 0.119,0.142 10 L 1.43,1.338 1.55,1.48 0.119,0.142 10 E 6.037,1.148 6.214,1.288 0.177,0.14 10 L2 6.037,1.708 6.311,1.848 0.274,0.14 10 UL3 6.037,3.964 6.214,4.104 0.177,0.14 10 L1 6.037,3.403 6.311,3.543 0.274,0.14 10 UL1 5.716,3.954 5.944,4.094 0.229,0.14 10 I13 5.716,3.394 5.944,3.534 0.229,0.14 10 I13 5.716,1.699 5.944,1.839 0.229,0.14 10 I13 5.716,1.138 5.944,1.278 0.229,0.14 10 I13 0.778,4.242 1.047,4.382 0.27,0.14 10 J10 0.778,1.902 0.955,2.042 0.177,0.14 10 J1 0.103,0.036 0.773,0.22 0.67,0.184 12 for RHD:

PROCEDURE

1.CHECK DOOR LOCK OPERATION

Result:
Result Proceed to
All doors cannot be locked through door control switch (power window regulator switch assembly) A
All doors cannot be locked through door key cylinder B



A

2.READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY))

B

5.CHECK DOOR LOCK OPERATION (DOOR KEY CYLINDER)
2.READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock SW-Lock Door control switch (power window regulator master switch assembly) lock signal ON or OFF ON: Lock side of door control switch (power window regulator master switch assembly) pushed
OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed
-
Door Lock SW-Unlock Door control switch (power window regulator master switch assembly) unlock signal ON or OFF ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed
-
Body Electrical > Main Body > Data List
Tester Display
Door Lock SW-Lock
Door Lock SW-Unlock
50003 123 17,18
OK:

The intelligent tester indicates ON or OFF according to the switch operation shown in the table above.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
3.INSPECT DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
a.

for LHD

i.
B279066
1.594,3.218 1.594,2.552 1.594,2.552 1.777,2.552 false 1.796,2.47 1.916,2.612 0.12,0.142 10 E 1.456,3.218 1.456,2.243 1.456,2.243 1.78,2.243 false 1.798,2.163 1.921,2.305 0.123,0.142 10 L 0.476,3.218 0.476,2.243 0.476,2.243 0.605,2.243 false 0.63,2.175 0.845,2.317 0.215,0.142 10 UL 0.153,0.103 0.302,0.273 0.149,0.17 10 *a
*a Component without harness connected
(Door Control Switch (Power Window Regulator Master Switch Assembly))


Remove the door control switch (power window regulator master switch assembly).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 1 (E) Lock switch pushed Below 1 Ω
2 (L) - 1 (E) off 10 kΩ or higher
9 (UL) - 1 (E) Unlock switch pushed Below 1 Ω
9 (UL) - 1 (E) off 10 kΩ or higher




b.

for RHD

i.
B295736
0.148,0.115 0.323,0.271 0.175,0.156 10 *a 0.469,3.214 0.469,1.959 0.469,1.959 0.787,1.959 false 0.604,3.227 0.604,2.482 0.604,2.482 0.784,2.482 false 1.448,3.228 1.448,2.483 1.448,2.483 1.689,2.483 false 0.823,2.406 1.028,2.549 0.205,0.142 10 UL 0.832,1.873 0.946,2.016 0.115,0.142 10 E 1.734,2.398 1.836,2.54 0.102,0.142 10 L
*a Component without harness connected
(Door Control Switch (Power Window Regulator Master Switch Assembly))


Remove the door control switch (power window regulator master switch assembly).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 9 (E) Lock switch pushed Below 1 Ω
2 (L) - 9 (E) off 10 kΩ or higher
8 (UL) - 9 (E) Unlock switch pushed Below 1 Ω
8 (UL) - 9 (E) off 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K10-2 (L) - I13-9 (L1) Always Below 1 Ω
K10-9 (UL) - I13-10 (UL1) Always Below 1 Ω
K10-1 (E) - Body ground Always Below 1 Ω
K10-2 (L) - Body ground Always 10 kΩ or higher
K10-9 (UL) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
J10-2 (L) - I13-9 (L1) Always Below 1 Ω
J10-8 (UL) - I13-10 (UL1) Always Below 1 Ω
J10-9 (E) - Body ground Always Below 1 Ω
J10-2 (L) - Body ground Always 10 kΩ or higher
J10-8 (UL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK DOOR LOCK OPERATION (DOOR KEY CYLINDER)
a.

Proceed to the next step according to the symptom if all the doors cannot be locked/unlocked at once.


Result:
Result Proceed to
All doors cannot be locked/unlocked at once by using door key cylinder on driver door. A
All doors cannot be locked/unlocked at once by using door key cylinder on front passenger door.* B
All doors cannot be locked/unlocked at once by using both driver door and front passenger door key cylinder.* C


*: w/o Wireless Door Lock Control Function



A

6.READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)))

B

9.READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (FRONT PASSENGER DOOR)))

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

6.READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Key SW-Lock Driver door and front passenger door* key-linked lock/unlock switch lock signal ON or OFF ON: Driver door or front passenger door* key cylinder turned to lock position
OFF: Driver door and front passenger door* key cylinder not turned to lock position
-
D Door Key SW-UL Driver door key-linked lock/unlock switch unlock signal ON or OFF ON: Driver door key cylinder turned to unlock position
OFF: Driver door key cylinder not turned to unlock position
-

*: w/o Wireless Door Lock Control Function


Body Electrical > Main Body > Data List
Tester Display
Door Key SW-Lock
D Door Key SW-UL
50003 123 19,21
OK:

The intelligent tester indicates ON or OFF according to the key cylinder operation shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

7.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)
7.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)
a.

Remove the front door lock with motor assembly (driver door).

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


b.
B280166
0.101,0.076 0.267,0.242 0.166,0.166 10 *a 2.851,1.623 3.017,1.789 0.166,0.166 10 *b 3.057,0.558 3.223,0.723 0.166,0.166 10 *c 2.273,3.437 2.273,3.802 2.273,3.802 2.086,3.802 false 2.427,3.437 2.427,4.115 2.427,4.115 1.931,4.115 false 2.737,3.437 2.737,4.436 2.737,4.436 2.086,4.436 false 1.927,4.36 2.042,4.503 0.115,0.142 10 E 1.807,4.034 1.908,4.176 0.101,0.142 10 L 1.816,3.716 2.027,3.858 0.212,0.142 10 UL
*a Component without harness connected
(Front Door Lock with Motor Assembly (Driver Door))
*b Lock
*c Unlock


for LHD

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Held to lock side Below 1 Ω
9 (L) - 7 (E) Neutral or held to unlock side 10 kΩ or higher
10 (UL) - 7 (E) Held to unlock side Below 1 Ω
10 (UL) - 7 (E) Neutral or held to lock side 10 kΩ or higher




c.
B284859
0.748,3.424 0.748,4.442 0.748,4.442 0.903,4.442 false 1.057,3.424 1.057,4.133 1.057,4.133 1.212,4.133 false 1.212,3.424 1.212,3.823 1.212,3.823 1.367,3.823 false 0.955,4.35 1.079,4.507 0.124,0.156 10 E 1.264,4.041 1.374,4.197 0.11,0.156 10 L 1.402,3.732 1.614,3.888 0.212,0.156 10 UL 0.084,0.033 0.233,0.204 0.149,0.17 10 *a 0.6,1.615 0.749,1.785 0.149,0.17 10 *b 0.342,0.515 0.491,0.685 0.149,0.17 10 *c
*a Component without harness connected
(Front Door Lock with Motor Assembly (Driver Door))
*b Lock
*c Unlock


for RHD

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Held to lock side Below 1 Ω
6 (L) - 8 (E) Neutral or held to unlock side 10 kΩ or higher
5 (UL) - 8 (E) Held to unlock side Below 1 Ω
5 (UL) - 8 (E) Neutral or held to lock side 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR)

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (DRIVER DOOR) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K1-9 (L) - I13-11 (L2) Always Below 1 Ω
K1-10 (UL) - I13-24 (UL3) Always Below 1 Ω
K1-7 (E) - Body ground Always Below 1 Ω
I13-11 (L2) - Body ground Always 10 kΩ or higher
I13-24 (UL3) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
J1-6 (L) - I13-11 (L2) Always Below 1 Ω
J1-5 (UL) - I13-24 (UL3) Always Below 1 Ω
J1-8 (E) - Body ground Always Below 1 Ω
I13-11 (L2) - Body ground Always 10 kΩ or higher
I13-24 (UL3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (FRONT PASSENGER DOOR)))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Key SW-Lock Driver door and front passenger door* key-linked lock/unlock switch lock signal ON or OFF ON: Driver door or front passenger door* key cylinder turned to lock position
OFF: Driver door and front passenger door* key cylinder not turned to lock position
-
Door Key SW-Unlock Front passenger door key-linked lock/unlock switch unlock signal ON or OFF ON: Front passenger door key cylinder turned to unlock position
OFF: Front passenger door key cylinder not turned to unlock position
-

*: w/o Wireless Door Lock Control Function


Body Electrical > Main Body > Data List
Tester Display
Door Key SW-Lock
Door Key SW-Unlock
50003 123 19,20
OK:

The intelligent tester indicates ON or OFF according to the key cylinder operation shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

10.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY (FRONT PASSENGER DOOR)
10.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY (FRONT PASSENGER DOOR)
a.
B280267
0.104,0.072 0.259,0.222 0.155,0.15 10 *a 0.636,1.913 0.792,2.063 0.155,0.15 10 *c 0.342,0.738 0.497,0.888 0.155,0.15 10 *b 0.772,3.514 0.772,4.445 0.772,4.445 1.367,4.445 false 1.047,3.514 1.047,4.13 1.047,4.13 1.367,4.13 false 1.185,3.514 1.185,3.809 1.185,3.809 1.367,3.809 false 1.387,4.353 1.504,4.496 0.117,0.142 10 E 1.387,4.044 1.497,4.186 0.11,0.142 10 L 1.387,3.729 1.596,3.871 0.209,0.142 10 UL
*a Component without harness connected
(Front Door Lock with Motor Assembly (Front Passenger Door))
*b Lock
*c Unlock


Remove the front door lock with motor assembly (front passenger door).

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Held to lock side Below 1 Ω
6 (L) - 8 (E) Neutral or held to unlock side 10 kΩ or higher
5 (UL) - 8 (E) Held to unlock side Below 1 Ω
5 (UL) - 8 (E) Neutral or held to lock side 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (FRONT PASSENGER DOOR) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE FRONT DOOR LOCK WITH MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

11.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY (FRONT PASSENGER DOOR) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-6 (L) - I13-11 (L2) Always Below 1 Ω
J1-5 (UL) - I13-12 (UL2) Always Below 1 Ω
J1-8 (E) - Body ground Always Below 1 Ω
I13-11 (L2) - Body ground Always 10 kΩ or higher
I13-12 (UL2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR