The linear solenoid valve (SLT) controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the current to SLT solenoid valve to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2714 | Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) | The ECM detects a malfunction in the shift solenoid valve SLT (ON side) according to the difference in the speed between the turbine and the output shaft, and also by the transmission fluid pressure. (2-trip detection logic) | ·
Shift solenoid valve SLT remains open ·
Shift solenoid valve SL1, SL2, SL3 or SL4 remains open or closed ·
Valve body is blocked ·
Automatic transaxle (clutch, brake or gear, etc.) |
Comes on | DTC stored |
The ECM calculates the amount of clutch slip based on the turbine speed, output shaft speed, and gear ratio. If the amount of clutch slip exceeds a specified level, the ECM will set this DTC and illuminate the MIL.
When shift solenoid valve SLT remains on, the line pressure goes down and clutch engagement force decreases.
If driving continues under these conditions, clutches will burn out and the vehicle will no longer be drivable.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs using the intelligent tester.
| Display (DTC Output) | Proceed to |
|---|---|
| Only "P2714" is output | A |
| "P2714" and other DTCs are output | B |
If a solenoid is stuck ON, DTCs for several solenoids including the malfunctioning solenoid will be detected.
A
B
Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F)
Be sure to prevent SST hose from interfering with the exhaust pipe.
This check must be conducted after checking and adjusting the engine.
Perform the test with the A/C OFF.
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the ignition switch off.
Lift the vehicle up.
Remove the test plug on the transmission case center right side and connect SST.
Lower the vehicle.
Fully apply the parking brake and chock the 4 wheels.
Connect the intelligent tester to the DLC3.
Start the engine.
Warm up the Automatic Transmission Fluid (ATF).
Measure the line pressure when the engine is idling.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Follow the instructions on the intelligent tester and perform the Active Test.
Measure the line pressure with SST.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the Solenoid (SLT) | Operates shift solenoid SLT to raise the line pressure. | ON/OFF
HINT: ON: No action (normal operation) OFF: Line pressure up (When the Active Test of "Activate the Solenoid (SLT)" is performed, the ECM commands the SLT solenoid to turn off). |
[Vehicle Condition]
·
Vehicle Stopped ·
IDL: ON |
| Tester Display |
|---|
| Activate the Solenoid (SLT) |
"Activate the Solenoid (SLT)" in the Active Test is performed to check that the line pressure changes by connecting the SST to the automatic transaxle. The same SST is used in the Hydraulic Test (Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>HYDRAULIC TEST) as well.
The pressure values in Active Test and Hydraulic Test are different from each other.
The line pressure changes as specified when performing the Active Test.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
This test should always be performed with at least 2 people.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Shift Position | Operates the shift solenoid valves to allow gears to selected manually. | ·
Press "→" button: Upshift occurs ·
Press "←" button: Downshift occurs |
Can be used to check the operation of the shift solenoid valves.
Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes. Do not downshift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition] 50 km/h (30 mph) or less |
| Tester Display |
|---|
| Control the Shift Position |
This test can be conducted when the vehicle is stopped.
When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.
The gear commanded by the ECM is shown in the Data List / Shift Status display on the intelligent tester.
Check the vehicle speed and the gear when the engine speed is 1000 rpm.
Because the torque converter has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th, and 6th gear, however a difference of speed should still be evident following each gear change.
| 1st | 2nd | 3rd | 4th | 5th | 6th |
|---|---|---|---|---|---|
| 8 to 12 km/h (5 to 7.5 mph) | 15 to 19 km/h (9.3 to 11.8 mph) | 21 to 25 km/h (13.0 to 15.5 mph) | 31 to 35 km/h (19.3 to 21.7 mph) | 44 to 48 km/h (27.3 to 29.8 mph) | 52 to 56 km/h (32.3 to 34.8 mph) |
Compare the ECM commanded gear and the actual gear.
| Actual Gear during Malfunction | ECM Commanded Gear | Proceed to | ||||||
|---|---|---|---|---|---|---|---|---|
| 1st | 2nd | 3rd | 4th | 5th | 6th | |||
| Shift solenoid SL1 | Stuck ON | 1st | 2nd | 3rd | 4th | 4th | 4th | A |
| Stuck OFF | N*1 | N*1 | N*1 | N*1 | 5th | 6th | ||
| Shift solenoid SL2 | Stuck ON | 4th | 4th | 4th | 4th | 5th | 6th | B |
| Stuck OFF | 1st | 2nd | 3rd | 1st | N*1 | N*1 | ||
| Shift solenoid SL3 | Stuck ON | 2nd | 2nd | 3rd | 4th | 5th | 6th | C |
| Stuck OFF | 1st | 1st | 3rd | 4th | 5th | N*1 | ||
| Shift solenoid SL4 | Stuck ON*3 | 3rd | 3rd | 3rd | 4th | 5th | 5th | D |
| Stuck OFF | 1st | 2nd | 1st | 4th | N*1 | 6th | ||
| Shift solenoid SLT | Stuck ON | N*2 | N*2 | N*2 | N*2 | N*2 | N*2 | E |
| Stuck OFF*3 | 1st | 2nd | 3rd | 4th | 5th | 6th | ||
*1: Neutral
*2: If shift solenoid SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.
*3: When shift solenoid SLT is stuck off, gear shifting is normal.
A
B
C
D
E
| *1 | Shift Solenoid Valve SLT |
Remove shift solenoid valve SLT.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.
Valve moves and makes an operating sound.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmission valve body assembly.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>REMOVAL
There are no foreign objects on each valve and they operate smoothly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE ASSEMBLY>COMPONENTS
NG