Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0076198 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0711  Transmission Fluid Temperature Sensor "A" Performance  


DESCRIPTION

The Automatic Transmission Fluid (ATF) temperature sensor converts the fluid temperature into a resistance value for use by the ECM.

C274654
1.833,1.458 1.531,1.896 false 0.313,0.646 1.844,0.844 1.531,0.198 10 Resistance 1.01,3.823 1.958,4.031 0.948,0.208 10 Temperature 1.917,1.385 3.104,1.594 1.188,0.208 10 Acceptable range

The ECM applies a voltage to the temperature sensor through terminal THO1 of the ECM.

The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.

The ECM calculates the fluid temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0711 Transmission Fluid Temperature Sensor "A" Performance One of the following conditions (A) or (B) is met:
(A) Both (a) and (b) are detected: (2-trip detection logic)
·

(a) Intake air and engine coolant temperatures are more than -10°C (14°F) at engine start


·

(b) After normal driving for over 18 min. and 20 sec. and 8 km (5 mile) or more, ATF temperature is less than 20°C (68°F)


(B) Both (a) and (b) are detected: (2-trip detection logic)
·

(a) Engine coolant temperature is less than 35°C (95°F) at engine start


·

(b) ATF temperature is 110°C (230°F) or more when engine coolant temperature reaches 60°C (140°F)


ATF temperature sensor Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates that there is a problem with output signals from the automatic transmission fluid (ATF) temperature sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the ATF temperature circuit or a fault of the ATF temperature sensor.

After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault turns on the MIL, and stores the DTC.

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0712 (See page Drivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>P0712).

CAUTION / NOTICE / HINT

DATA LIST


NOTICE:

In the table below, the value listed under "Normal Condition" are reference values.


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the intelligent tester, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 215°C (419°F)
·

After stall speed test: Approximately 80°C (176°F)

·

Equal to ambient temperature when cold soak


If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or short circuited
Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Temperature 1
50003 234 406
HINT:

When DTC P0712 is output and the intelligent tester indicates 150°C (302°F) or more, there is a short circuit.

When DTC P0713 is output and the intelligent tester indicates -40°C (-40°F), there is an open circuit.

Measure the resistance between terminal THO1 (OIL) and body ground.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or more Short circuit

HINT:

If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected.

It is not necessary to inspect the circuit when P0711 is set.




PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0711)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the intelligent tester.

Result:
Display (DTC Output) Proceed to
Only P0711 is output A
P0711 and other DTC B


HINT:

If any other codes besides P0711 are output, perform troubleshooting for those DTCs first.




A

2.CHECK TRANSMISSION FLUID LEVEL

B

2.CHECK TRANSMISSION FLUID LEVEL

OK:

Automatic transmission fluid level is correct.


Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)

NG

ADJUST FLUID LEVEL