Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.10–2016.05
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076218 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1428  Motor Circuit Malfunction  


DESCRIPTION

This DTC is stored when the skid control ECU judges that an abnormality occurred in the circuit used to operate the pump motor.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1428 Motor Circuit Malfunction A malfunction occurs in the pump motor circuit. Pump motor circuit

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)
a.
C238832C24
0.208,0.698 0.688,1.021 0.479,0.323 1.24,2.667 0.802,1.917 false 0.271,0.177 0.573,0.563 0.302,0.385 10 *a 0.333,0.781 0.76,1.094 0.427,0.313 10 A49 1.052,2.688 1.406,2.844 0.354,0.156 10 +BM
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A49 skid control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-1 (+BM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
C238832C25
0.208,0.698 0.688,1.021 0.479,0.323 2.458,2.677 2.792,1.917 false 0.271,0.177 0.594,0.521 0.323,0.344 10 *a 0.344,0.781 0.906,1.125 0.563,0.344 10 A49 2.188,2.708 2.698,2.99 0.51,0.281 10 GND2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the A49 skid control ECU connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1428 is not output. A
DTC C1428 is output. B



A

B