Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.10–2016.05
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076218 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C146C  Open in ABS Motor Relay Circuit  


DESCRIPTION

The ABS motor relay supplies power to the pump motor. While the ABS is activated, the skid control ECU turns the ABS motor relay on to operate the pump motor.

If the voltage supplied to the ABS motor relay (+BM) is too low due to low voltage from the battery or alternator, the DTC may be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C146C Open in ABS Motor Relay Circuit Any of the following is detected:
1.

When the ABS motor relay is actuated, voltage is not supplied to the pump motor.

2.

When the ABS motor relay is not actuated, voltage in the pump motor is high.

3.

The skid control ECU judges that pump motor operation is abnormal.


·

ABS NO. 1 fuse (Fusible link block assembly)

·

ABS motor relay circuit

·

ABS motor relay (Brake actuator assembly)



WIRING DIAGRAM

C249047E01
0.844,4.115 1.333,4.281 0.49,0.167 10 Battery 1.865,1.552 2.573,1.729 0.708,0.177 10 ABS NO. 1 3.615,1.292 3.813,1.438 0.198,0.146 10 1 3.802,1.521 4.25,1.688 0.448,0.167 10 +BM 4.583,5.26 6.24,5.427 1.656,0.167 10 Brake Actuator Assembly 5.146,2.417 6.26,2.573 1.115,0.156 10 Skid Control ECU 5.167,1.396 6.26,1.552 1.094,0.156 10 ABS Motor Relay 5.365,4.479 6.167,4.635 0.802,0.156 10 Pump Motor 4.583,5.115 4.854,5.26 0.271,0.146 10 A49 3.531,3.281 3.729,3.427 0.198,0.146 10 13 3.802,3.49 4.208,3.635 0.406,0.146 10 GND2 0.771,2.688 1.396,2.865 0.625,0.177 10 FL MAIN

CAUTION / NOTICE / HINT

HINT:

When C1241 and/or C1417 is output together with C146C, inspect and repair the trouble areas indicated by C1241 and/or C1417 first.

for C1241: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1241

for C1417: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1417


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Select the Active Test using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Motor Relay ABS motor relay Relay ON/OFF Operating sound of motor can be heard
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Motor Relay
50004 105 2

d.

Check the operating sound of the pump motor when operating it using the intelligent tester.


Result:
Result Proceed to
Operating sound is heard. A
Operating sound is not heard. B



A

2.RECONFIRM DTC

B

3.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)
2.RECONFIRM DTC
HINT:

This DTC is stored when a problem is identified in the brake actuator assembly.

The ABS motor relay is in the brake actuator assembly.

Therefore, motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if the DTC is output again before replacing the brake actuator assembly.


a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for 30 seconds or more.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C146C is not output. A
DTC C146C is output. B


HINT:
·

If a speed signal of 40 km/h (25 mph) or more is received by the skid control ECU with the ignition switch ON, the skid control ECU performs self diagnosis of the motor circuit.

·

If the normal system code is output (No DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B

3.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)
a.
C238832C26
0.208,0.698 0.688,1.021 0.479,0.323 1.24,2.667 0.802,1.917 false 0.271,0.177 0.469,0.333 0.198,0.156 10 *a 0.333,0.781 0.927,1.135 0.594,0.354 10 A49 1.052,2.688 1.406,2.844 0.354,0.156 10 +BM
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Check that the ABS NO. 1 (50 A) fuse is normal.

HINT:

If the result is not as specified, replace the ABS NO. 1 fuse (fusible link block assembly).



b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A49 skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-1 (+BM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
C238832C27
0.208,0.698 0.688,1.021 0.479,0.323 2.458,2.677 2.802,1.927 false 0.271,0.177 0.698,0.542 0.427,0.365 10 *a 0.344,0.781 0.823,1.073 0.479,0.292 10 A49 2.188,2.708 2.604,2.865 0.417,0.156 10 GND2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)