Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.10–2016.05
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076218 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C146E  Open in ABS Solenoid Relay Circuit  


DESCRIPTION

The ABS solenoid relay is built into the skid control ECU in the brake actuator assembly.

The ABS solenoid relay supplies power to the ABS solenoid.

The skid control ECU detects a solenoid relay malfunction by performing a self check and relay operation check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C146E Open in ABS Solenoid Relay Circuit Either of the following is detected:
1.

A solenoid relay drive circuit in the skid control ECU is malfunctioning.

2.

The solenoid relay cannot be switched between on and off.


·

ABS NO. 2 fuse (Fusible link block assembly)

·

ABS solenoid relay circuit

·

ABS solenoid relay (Brake actuator assembly)



WIRING DIAGRAM

C250531E01
1.625,1.341 2.374,1.52 0.749,0.179 10 ABS NO. 2 4.404,8.248 4.675,8.392 0.271,0.144 10 A49 3.266,1.082 3.452,1.226 0.187,0.144 10 25 3.266,4.982 3.498,5.121 0.233,0.139 10 38 0.717,6.844 1.223,7.017 0.506,0.173 10 Battery 3.537,5.188 3.962,5.331 0.425,0.144 10 GND1 3.537,1.299 3.867,1.454 0.331,0.155 10 +BS 4.469,4.304 5.616,4.477 1.147,0.173 10 Skid Control ECU 4.404,8.388 6.045,8.565 1.641,0.177 10 Brake Actuator Assembly 4.582,0.958 5.52,1.283 0.939,0.325 10 ABS Solenoid Relay 5.971,2.313 6.379,2.458 0.407,0.145 10 SFRH 5.971,3.074 6.377,3.249 0.406,0.175 10 SFLH 5.971,3.853 6.393,4.024 0.422,0.171 10 SRRH 5.971,4.615 6.403,4.782 0.431,0.167 10 SRLH 5.971,5.382 6.375,5.522 0.404,0.139 10 SFRR 5.971,6.131 6.354,6.277 0.383,0.146 10 SFLR 5.971,6.89 6.389,7.034 0.418,0.143 10 SRRR 5.971,7.658 6.364,7.802 0.393,0.144 10 SRLR 0.635,4.073 1.384,4.252 0.749,0.179 10 FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

When C1241 and/or C1417 is output together with C146E, inspect and repair the trouble areas indicated by C1241 and/or C1417 first.

for C1241: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1241

for C1417: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1417


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
a.
C238832C28
0.208,0.719 0.688,1.042 0.479,0.323 0.76,1.5 1.365,0.75 false 0.271,0.198 0.625,0.542 0.354,0.344 10 *a 0.333,0.802 0.802,1.198 0.469,0.396 10 A49 1.26,0.563 1.625,0.906 0.365,0.344 10 +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A49 skid control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-25 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C238832C29
0.208,0.719 0.688,1.042 0.479,0.323 2.823,1.5 2.219,0.75 false 0.271,0.198 0.583,0.521 0.313,0.323 10 *a 0.333,0.802 0.854,1.094 0.521,0.292 10 A49 1.948,0.563 2.583,0.865 0.635,0.302 10 GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-38 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

3.RECONFIRM DTC
HINT:

This DTC is stored when a problem is identified in the brake actuator assembly.

The solenoid circuits are located in the brake actuator assembly.

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if the DTC is output again before replacing the brake actuator assembly.


a.

Reconnect the A49 skid control ECU connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C146E is not output. A
DTC C146E is output. B


HINT:
·

The skid control ECU performs self diagnosis of the solenoid circuit after the ignition switch is turned to ON.

·

If the normal system code is output (No DTCs are output), slightly jiggle the connectors, wire harnesses, and fuses of the brake actuator assembly.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B