Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076219 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1225  SM Solenoid Circuit  C1226  SA2 Solenoid Circuit  C1227  SA3 Solenoid Circuit  C1228  STR Solenoid Circuit  C1468  SFR Solenoid Circuit  C1469  SFL Solenoid Circuit  C146A  SRR Solenoid Circuit  C146B  SRL Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1225 SM Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


C1226 SA2 Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


C1227 SA3 Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


C1228 STR Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


C1468 SFR Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


C1469 SFL Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


C146A SRR Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


C146B SRL Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)



PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the brake actuator assembly.

The solenoid circuits are in the brake actuator assembly.

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTC is output before replacing the brake actuator assembly.


a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1225, C1226, C1227, C1228, C1468, C1469, C146A and C146B are not output. A
DTCs C1225, C1226, C1227, C1228, C1468, C1469, C146A and/or C146B are output. B


HINT:
·

The skid control ECU performs self diagnosis of the solenoid circuit after the ignition switch is turned to ON.

·

If the normal system code is output (No DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B