Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0073970 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control switch turn on with switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM

E229591E21
6.331,0.834 6.675,0.99 0.344,0.156 10 CCS 6.345,1.525 6.536,1.681 0.191,0.156 10 E1 5.944,1.516 6.218,1.672 0.274,0.156 10 E26 5.996,1.322 6.18,1.478 0.184,0.156 10 16 5.06,3.075 5.164,3.232 0.104,0.156 10 1 5.057,3.968 5.166,4.124 0.109,0.156 10 2 3.991,3.075 4.091,3.232 0.101,0.156 10 3 3.985,3.968 4.097,4.124 0.111,0.156 10 4 5.996,0.636 6.18,0.792 0.184,0.156 10 40 5.953,0.834 6.227,0.99 0.274,0.156 10 A25 4.998,3.3 5.272,3.456 0.274,0.156 10 I28 4.998,4.192 5.272,4.349 0.274,0.156 10 I28 3.95,3.295 4.123,3.451 0.174,0.156 10 z2 4.553,3.191 4.876,3.347 0.323,0.156 10 CCS 6.47,5.208 6.849,5.364 0.378,0.156 10 ECM 4.553,4.102 4.876,4.258 0.323,0.156 10 ECC 3.946,4.188 4.127,4.344 0.181,0.156 10 z2 1.154,4.707 2.624,4.867 1.47,0.16 10 Cruise Control Switch 3.402,4.809 4.368,5.132 0.966,0.323 10 Cruise Control Switch Wire 3.107,4.292 3.43,4.448 0.323,0.156 10 ECC 3.107,3.186 3.43,3.343 0.323,0.156 10 CCS 3.517,3.178 3.677,3.334 0.16,0.156 10 3 3.517,4.292 3.656,4.448 0.138,0.156 10 1 2.877,3.756 3.437,3.912 0.559,0.156 10 ON-OFF 2.11,3.756 2.576,3.912 0.466,0.156 10 +/RES 1.347,3.756 1.748,3.912 0.401,0.156 10 -/SET 0.527,3.756 1.114,3.912 0.587,0.156 10 CANCEL 4.413,4.696 5.356,5.062 0.944,0.366 10 Spiral Cable Sub-assembly

PROCEDURE

1.READ VALUE ON INTELLIGENT TESTER
a.
E107091C01
2.144,0.084 2.42,0.273 0.276,0.189 10 *c 2.763,1.172 3.003,1.374 0.24,0.202 10 *a 1.934,1.577 2.325,1.779 0.391,0.202 10 *b 1.033,1.235 1.268,1.437 0.235,0.202 10 *d
*a ON-OFF
*b -/SET
*c +/RES
*d CANCEL


Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Select the following menu items: Powertrain / Cruise Control / Data List.


e.

Check the Data List to confirm proper functioning of the cruise control switch.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control switch signal (Main CPU) ON or OFF ON: Cruise control switch (ON-OFF button) pushed
OFF: Cruise control switch (ON-OFF button) released
-
Cancel Switch Switch CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -/SET switch signal ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
RES/ACC Switch +/RES switch signal ON or OFF ON: +/RES switch on
OFF: +/RES switch off
-
Powertrain > Cruise Control > Data List
Tester Display
Main SW M-CPU
Cancel Switch
SET/COAST Switch
RES/ACC Switch
50003 237 16,23,22,21
OK:

When the cruise control switch is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL SWITCH
2.INSPECT CRUISE CONTROL SWITCH
a.

b.

Measure the resistance according to the value(s) in the table below.

E265511C01
5.021,1.167 5.5,0.667 5.5,0.667 5.75,0.667 false 5.781,0.583 6.094,0.74 0.313,0.156 10 *1 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 5.917,1.25 6.229,1.406 0.313,0.156 10 *b 4.604,0.583 4.917,0.74 0.313,0.156 10 *c 5.021,2.344 5.333,2.5 0.313,0.156 10 *d 3.833,2.167 4.146,2.323 0.313,0.156 10 *e
*1 Cruise Control Switch (ON-OFF button) - -
*a Component without harness connected
(Cruise Control Switch)
*b ON-OFF
*c +/RES *d -/SET
*e CANCEL - -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 3 Cruise control switch (ON-OFF button) released 1 MΩ or higher
Cruise control switch (ON-OFF button) pushed Below 2.5 Ω
+/RES 235 to 245 Ω
-/SET 617 to 643 Ω
CANCEL 1509 to 1571 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL SWITCH WIRE

NG

3.CHECK CRUISE CONTROL SWITCH WIRE
a.
E232246C01
0.24,1.344 0.667,1.646 0.427,0.302 0.333,0.854 0.5,1.031 0.167,0.177 10 *a 0.333,3.177 0.5,3.354 0.167,0.177 10 *b 0.396,1.406 0.833,1.76 0.438,0.354 10 z2
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Switch)


Disconnect the spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Specified Condition
Cruise control switch side connector terminal 3 - z2-3 Below 1 Ω
Cruise control switch side connector terminal 1 - z2-4 Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE CRUISE CONTROL SWITCH WIRE

4.CHECK SPIRAL CABLE SUB-ASSEMBLY
NOTICE:

The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.


HINT:


E265512C01
2.25,0.25 2.5,0.417 0.25,0.167 1.583,4.083 1.833,4.25 0.25,0.167 1.74,3.281 2.167,3.083 false 1.74,3.365 2.167,3.531 false 0.104,0.094 0.417,0.25 0.313,0.156 10 *a 2.313,0.25 2.625,0.448 0.313,0.198 10 z2 1.625,4.083 2.083,4.281 0.458,0.198 10 I28 2.208,3 2.667,3.198 0.458,0.198 10 CCS 2.208,3.469 2.667,3.667 0.458,0.198 10 ECC
*a Component without harness connected
(Spiral Cable Sub-assembly)


a.

Remove the spiral cable sub-assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z2-3 - I28-1 (CCS) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right
z2-4 - I28-2 (ECC) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right



c.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z2-3 - I28-1 (CCS) Always Below 3 Ω
z2-4 - I28-2 (ECC) Always Below 3 Ω


HINT:

The spiral cable sub-assembly makes a maximum of approximately 5 rotations.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A25-40 (CCS) - I28-1 (CCS) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A25-40 (CCS) or I28-1 (CCS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I28-2 (ECC) - Body ground Always Below 1 Ω



E229999C01
0.531,1.719 0.823,1.969 0.292,0.25 0.948,2.552 1.458,1.885 false 0.594,1.781 1.052,1.979 0.458,0.198 10 false I28 0.135,0.115 0.594,0.313 0.458,0.198 10 false *a 0.76,2.615 1.219,2.813 0.458,0.198 10 false ECC
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)