Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ VSC) › 2011.10–2015.04
RM19V0EQ _58 Vehicle Interior _014610 SUPPLEMENTAL RESTRAINT SYSTEMS _0074148 AIRBAG SYSTEM(w/ VSC) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC)  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located on the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage. In addition, when the voltage drops, the SRS warning light will illuminate.

A malfunction in this circuit is not stored in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C249050E05
0.729,1.896 1.51,2.229 0.781,0.333 10 from Battery 0.229,3.917 2.906,4.229 2.677,0.313 10 *1: w/o Smart Entry and Start System 0.229,4.219 2.677,4.458 2.448,0.24 10 *2: w/ Smart Entry and Start System 5.146,0.802 5.5,1.115 0.354,0.313 10 A/B 2.094,1.479 2.865,1.771 0.771,0.292 10 METER-IG2 2.063,2.042 2.917,2.354 0.854,0.313 10 ECU-B NO. 1 3.135,2.448 3.417,2.823 0.281,0.375 10 ES 2.927,1.792 3.156,2.198 0.229,0.406 10 1 2.854,1.219 3.146,1.594 0.292,0.375 10 13 5.792,1.198 6.229,1.625 0.438,0.427 10 13 4.115,1.188 4.385,1.594 0.271,0.406 10 16 2.927,2.333 3.167,2.719 0.24,0.385 10 7 6.063,0.656 6.448,1.01 0.385,0.354 10 IG2 3.594,1.313 4.115,1.719 0.521,0.406 10 CANH 3.604,1.906 4.156,2.438 0.552,0.531 10 CANL 6.063,2.427 6.458,2.844 0.396,0.417 10 E1 6.063,2.938 6.344,3.302 0.281,0.365 10 E2 6.01,3.729 6.323,4.063 0.313,0.333 10 I47 3.052,3.708 3.313,4.104 0.26,0.396 10 I18 6.01,3.865 6.938,4.438 0.927,0.573 10 Airbag Sensor Assembly 3.052,3.885 4.24,4.458 1.188,0.573 10 Combination Meter Assembly 5.792,1.74 6.219,2.135 0.427,0.396 10 22 6.063,1.323 6.604,1.677 0.542,0.354 10 CANH 6.063,1.885 6.604,2.281 0.542,0.396 10 CANL 5.792,0.573 6.156,0.917 0.365,0.344 10 21 5.792,2.344 6.146,2.75 0.354,0.406 10 25 5.792,2.844 6.135,3.25 0.344,0.406 10 26 4.115,1.75 4.396,2.229 0.281,0.479 10 15 0.563,1.344 1.5,1.646 0.938,0.302 10 from IG2 Relay 2.896,0.646 3.99,0.958 1.094,0.313 10 from IG2 Relay*2 2.615,0.25 3.958,0.531 1.344,0.281 10 from Ignition Switch*1 3.135,1.896 3.406,2.219 0.271,0.323 10 B 3.146,1.333 3.448,1.656 0.302,0.323 10 IG+ 0.76,4.49 2.531,4.75 1.771,0.26 10 : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK SRS WARNING LIGHT OPERATION
a.

Check the SRS warning light operation approximately 6 seconds after the ignition switch is turned to ON.


Result:
SRS Warning Light Illumination Proceed to
Remains on A
Goes off and then comes on again B



A

2.CHECK BATTERY VOLTAGE

B

6.CHECK CAN COMMUNICATION SYSTEM
2.CHECK BATTERY VOLTAGE
a.

Measure the voltage of the battery.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR

NG

3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the airbag sensor assembly.

OK:
:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the airbag sensor assembly.


e.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)

NG

REPLACE WIRE HARNESS

4.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)
a.
C126715C06
0.49,0.865 0.833,1.094 0.344,0.229 1.292,1.281 0.854,1.708 false 1.656,1.281 1.219,1.708 false 1.75,1.292 2.188,1.719 false 0.031,0.031 0.313,0.396 0.281,0.365 10 *a 0.573,0.896 0.948,1.219 0.375,0.323 10 I47 0.729,1.719 1.135,2.073 0.406,0.354 10 IG2 1.125,1.729 1.49,2.063 0.365,0.333 10 E1 2.146,1.729 2.521,2 0.375,0.271 10 E2
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I47-21 (IG2) - Body ground Ignition switch ON 8 to 16 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-25 (E1) - Body ground Always Below 1 Ω
I47-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK SRS WARNING LIGHT

NG

REPLACE WIRE HARNESS

5.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch to ON.


b.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and turns back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY

6.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

HINT:
·

Refer to Bus Check for the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

The airbag sensor assembly is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system.




Result:
Result Proceed to
DTC is not output A
DTC is output B



A

7.CHECK BATTERY VOLTAGE

B

7.CHECK BATTERY VOLTAGE
a.

Measure the voltage of the battery.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK CONNECTOR

NG

8.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the airbag sensor assembly.

OK:
:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the airbag sensor assembly.


e.

Check that the terminal of the connector is not damaged.

OK:
The terminal is not deformed or damaged.:


Result:
Proceed to
OK
NG



OK

9.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)

NG

REPLACE WIRE HARNESS

9.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)
a.
C126715C06
0.49,0.865 0.833,1.094 0.344,0.229 1.292,1.281 0.854,1.708 false 1.656,1.281 1.219,1.708 false 1.75,1.292 2.188,1.719 false 0.031,0.031 0.313,0.396 0.281,0.365 10 *a 0.573,0.896 0.948,1.219 0.375,0.323 10 I47 0.729,1.719 1.135,2.073 0.406,0.354 10 IG2 1.125,1.729 1.49,2.063 0.365,0.333 10 E1 2.146,1.729 2.521,2 0.375,0.271 10 E2
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I47-21 (IG2) - Body ground Ignition switch ON 8 to 16 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-25 (E1) - Body ground Always Below 1 Ω
I47-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK CONNECTOR

NG

REPLACE WIRE HARNESS

10.CHECK CONNECTOR
a.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



b.

Check that the connector is properly connected to the combination meter assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



c.

Disconnect the connector from the combination meter assembly.


d.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE CONNECTOR

11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)
a.
C126720C05
0.125,0.406 0.479,0.635 0.354,0.229 0.844,1.365 0.51,1.552 false 0.833,1.125 0.5,0.927 false 1.792,1.208 2.167,1.823 false 0.094,0.052 0.354,0.323 0.26,0.271 10 *a 0.25,1.479 0.698,1.813 0.448,0.333 10 IG+ 2.094,1.854 2.5,2.083 0.406,0.229 10 ES 0.375,0.833 0.698,1.135 0.323,0.302 10 B 0.219,0.438 0.667,0.729 0.448,0.292 10 I18
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I18-13 (IG+) - Body ground Ignition switch ON 11 to 14 V
I18-1 (B) - Body ground Always 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-7 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE WIRE HARNESS

12.CHECK SRS WARNING LIGHT
a.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



b.

Connect the connector to the combination meter assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON.


e.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and turns back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY