Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/o VSC) › 2011.10–2016.05
RM19V0EQ _58 Vehicle Interior _014610 SUPPLEMENTAL RESTRAINT SYSTEMS _0074159 AIRBAG SYSTEM(w/o VSC) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o VSC)  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are displayed by blinking of the SRS warning light.

HINT:
·

When multiple warning lights in the combination meter blink continuously, a ground short in the wiring or an ECU connected to terminal TC of the DLC3 is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU including the airbag sensor assembly. Thus when multiple systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C248718E20
0.729,4.052 1.281,4.396 0.552,0.344 10 false ECM 0.729,3.906 1.25,4.167 0.521,0.26 10 false A25 1.375,1.229 1.865,1.677 0.49,0.448 10 false 26 1.375,0.531 1.813,0.771 0.438,0.24 10 false 13 1.385,2.646 1.844,3.042 0.458,0.396 10 false 23 0.917,1.385 1.698,1.813 0.781,0.427 10 false CANL 0.896,0.688 1.615,1.042 0.719,0.354 10 false CANH 5.958,2.75 6.333,3.083 0.375,0.333 10 false TC 1.104,2.75 1.854,3.167 0.75,0.417 10 false TC 5.719,2.656 6.063,2.958 0.344,0.302 10 false 13 5.781,3.271 6.115,3.51 0.333,0.24 10 false 4 5.958,3.375 6.323,3.635 0.365,0.26 10 false CG 6.167,3.906 6.552,4.208 0.385,0.302 10 false I39 6.167,4.063 6.646,4.396 0.479,0.333 10 false DLC3 5.958,1.396 6.448,1.698 0.49,0.302 10 false CANL 5.542,1.823 5.875,2.083 0.333,0.26 10 false I47 5.708,1.25 6.042,1.531 0.333,0.281 10 false 22 5.698,0.542 6.021,0.917 0.323,0.375 10 false 13 5.958,0.688 6.469,1.073 0.51,0.385 10 false CANH 5.542,1.99 7.125,2.375 1.583,0.385 10 false Airbag Sensor Assembly 0.771,4.438 2.542,4.708 1.771,0.271 10 false : CAN Communication Line

PROCEDURE

1.CHECK WIRE HARNESS (TC OF DLC3 - TC OF ECM)
a.
C238361C05
0.552,2.219 0.896,2.458 0.344,0.24 0.552,0.167 0.885,0.417 0.333,0.25 1.792,1.208 1.792,1.542 true 2.406,3.313 2.406,2.552 2.406,2.552 2.625,2.552 true 0.167,0.167 0.427,0.458 0.26,0.292 10 false *1 0.167,2.052 0.438,2.354 0.271,0.302 10 false *a 1.719,1.563 2.125,1.865 0.406,0.302 10 false TC 0.604,2.25 1.01,2.521 0.406,0.271 10 false A25 0.625,0.208 0.979,0.521 0.354,0.313 10 false I39 2.677,2.479 2.979,2.75 0.302,0.271 10 false TC
*1 DLC3
*a Front view of wire harness connector
(to ECM)


Turn the ignition switch off.


b.

Disconnect the connector from the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-13 (TC) - A25-23 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)
a.
C204945C03
0.094,0.615 0.427,0.833 0.333,0.219 1.615,0.802 1.615,0.302 1.615,0.302 1.813,0.302 false 0.156,0.135 0.469,0.396 0.313,0.26 10 *1 0.177,0.646 0.49,0.948 0.313,0.302 10 I39 1.854,0.219 2.25,0.469 0.396,0.25 10 CG
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)
a.
C204945C04
0.156,0.594 0.49,0.823 0.333,0.229 1.958,1.76 1.792,1.76 1.792,1.76 1.792,1.344 false 0.125,0.115 0.406,0.396 0.281,0.281 10 *1 0.24,0.625 0.802,1.083 0.563,0.458 10 I39 2.021,1.688 2.354,1.979 0.333,0.292 10 TC
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-13 (TC) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE WIRE HARNESS OR REPLACE ECM