Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM19V0EQ _58 Vehicle Interior _014611 SEAT _0074168 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2651  Reclining Sensor Malfunction  


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite forward or backward movement of the seatback by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2651 Reclining Sensor Malfunction The forward and backward lock detection position of the sensor is the same.
·

Position control ECU and switch assembly

·

Reclining motor (Separate type front seatback spring assembly)

·

Wire harness or connector



WIRING DIAGRAM

B348529
0.865,3.833 2.75,4.292 1.885,0.458 10 false Separate Type Front Seatback Spring Assembly 1.302,3.083 1.615,3.281 0.313,0.198 10 false f3 1.292,3.24 2.438,3.469 1.146,0.229 10 false Reclining Motor 2.25,1.573 2.406,1.771 0.156,0.198 10 false 1 2.26,1.083 2.417,1.281 0.156,0.198 10 false 4 2.26,2.063 2.417,2.26 0.156,0.198 10 false 2 2.25,2.583 2.406,2.781 0.156,0.198 10 false 3 4.813,1.177 5.271,1.375 0.458,0.198 10 false d11 4.823,1.677 5.281,1.875 0.458,0.198 10 false d11 4.813,2.188 5.271,2.385 0.458,0.198 10 false d12 4.813,2.688 5.271,2.885 0.458,0.198 10 false d12 4.896,1 5.146,1.198 0.25,0.198 10 false 9 4.854,2.021 5.104,2.219 0.25,0.198 10 false 11 4.885,2.521 5.135,2.719 0.25,0.198 10 false 1 4.854,1.521 5.104,1.719 0.25,0.198 10 false 11 5.135,1.698 5.75,1.896 0.615,0.198 10 false RCL- 5.135,1.188 5.75,1.385 0.615,0.198 10 false RCL+ 5.125,2.208 5.74,2.406 0.615,0.198 10 false SSRR 5.125,2.719 5.74,2.917 0.615,0.198 10 false SGND 4.854,3.844 6.448,4.302 1.594,0.458 10 false Position Control ECU and Switch Assembly

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RECLINING MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
OK:

Motor operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)

NG

5.INSPECT RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY)
2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)
a.

Disconnect the f3 reclining motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
f3-2 - f3-3 Reclining switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

3.CHECK RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
3.CHECK RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY)
a.
B238515
1.521,0.24 1.948,0.531 0.427,0.292 0.115,0.115 0.573,0.698 0.458,0.583 10 false *a 1.688,0.302 2.01,0.531 0.323,0.229 10 false f3
*a Component with harness connected
(Reclining Motor (Separate Type Front Seatback Spring Assembly))


Reconnect the f3 reclining motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
f3-2 - Body ground Reclining switch on 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPLACE RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
a.

Disconnect the d12 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d12-11 (SSRR) - f3-2 Always Below 1 Ω
d12-1 (SGND) - f3-3 Always Below 1 Ω
d12-11 (SSRR) - Body ground Always 10 kΩ or higher
d12-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU & SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY)
a.
B238256
0.107,0.047 0.272,0.21 0.165,0.162 10 *a
*a Component without harness connected
(Reclining Motor (Separate Type Front Seatback Spring Assembly))


Disconnect the f3 reclining motor connector.


b.

Check if the seatback moves smoothly when the battery is connected to the reclining motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1
Seatback moves forward
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4
Seatback moves backward



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)

NG

REPLACE RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
a.

Disconnect the d11 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d11-9 (RCL+) - f3-4 Always Below 1 Ω
d11-11 (RCL-) - f3-1 Always Below 1 Ω
d11-9 (RCL+) - Body ground Always 10 kΩ or higher
d11-11 (RCL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR