When the position control ECU and switch assembly does not receive a sensor signal despite upward or downward movement of the front of the seat cushion by power seat motor operation, this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2652 | Front Vertical Sensor Malfunction | The upward and downward lock detection position of the sensor the same. | ·
Position control ECU and switch assembly ·
Front vertical motor (Separate type front seat cushion spring assembly) ·
Wire harness or connector |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Driver Seat / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Tester Display |
|---|
| Front Vertical Operation |
Motor operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the d9 front vertical motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d9-2 - d9-3 | Front vertical switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Front Vertical Motor (Separate Type Front Seat Cushion Spring Assembly)) |
Reconnect the d9 front vertical motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| d9-2 - Body ground | Front vertical switch on | 4.5 to 4.8 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the d12 position control ECU and switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d12-3 (SSFV) - d9-2 | Always | Below 1 Ω |
| d12-1 (SGND) - d9-3 | Always | Below 1 Ω |
| d12-3 (SSFV) - Body ground | Always | 10 kΩ or higher |
| d12-1 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Front Vertical Motor (Separate Type Front Seat Cushion Spring Assembly)) |
Disconnect the d9 front vertical motor connector.
Check if the seat cushion spring moves smoothly when the battery is connected to the front vertical motor connector terminals.
| Measurement Condition | Operational Direction |
|---|---|
| Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1 |
Seat cushion spring moves upward |
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4 |
Seat cushion spring moves downward |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the d11 position control ECU and switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d11-8 (FRV+) - d9-4 | Always | Below 1 Ω |
| d11-5 (FRV-) - d9-1 | Always | Below 1 Ω |
| d11-8 (FRV+) - Body ground | Always | 10 kΩ or higher |
| d11-5 (FRV-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG