This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2658 | Short in Sensor with Motor Power Supply Circuit | Problem with the voltage supplied to the position control sensor. | ·
Position control ECU and switch assembly ·
Separate type front seat cushion spring assembly ·
Separate type front seatback spring assembly ·
Wire harness or connector |
Clear the DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR
DTC B2658 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the d12 position control ECU and switch assembly connector.
Disconnect the d8 slide motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d12-5 (SSRS) - d8-2 | Always | Below 1 Ω |
| d12-1 (SGND) - d8-3 | Always | Below 1 Ω |
| d12-5 (SSRS) - d12-1 (SGND) | Always | 10 kΩ or higher |
| d12-5 (SSRS) - Body ground | Always | 10 kΩ or higher |
| d12-1 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d8-2 - d8-3 | Sliding switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the d9 front vertical motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d12-3 (SSFV) - d9-2 | Always | Below 1 Ω |
| d12-1 (SGND) - d9-3 | Always | Below 1 Ω |
| d12-3 (SSFV) - d12-1 (SGND) | Always | 10 kΩ or higher |
| d12-3 (SSFV) - Body ground | Always | 10 kΩ or higher |
| d12-1 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d9-2 - d9-3 | Front vertical switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the d10 lifter motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d12-4 (SSRL) - d10-2 | Always | Below 1 Ω |
| d12-1 (SGND) - d10-3 | Always | Below 1 Ω |
| d12-4 (SSRL) - d12-1 (SGND) | Always | 10 kΩ or higher |
| d12-4 (SSRL) - Body ground | Always | 10 kΩ or higher |
| d12-1 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d10-2 - d10-3 | Lifter switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the separate type front seat cushion spring assembly.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY
Clear the DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR
DTC B2658 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the d12 position control ECU and switch assembly connector.
Disconnect the f3 reclining motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d12-11 (SSRR) - f3-2 | Always | Below 1 Ω |
| d12-1 (SGND) - f3-3 | Always | Below 1 Ω |
| d12-11 (SSRR) - d12-1 (SGND) | Always | 10 kΩ or higher |
| d12-11 (SSRR) - Body ground | Always | 10 kΩ or higher |
| d12-1 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| f3-2 - f3-3 | Reclining switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the separate type front seatback spring assembly.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY
Clear the DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR
DTC B2658 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG