Signals are input into the position control ECU and switch assembly. The built-in ECU manages the signals received from the front power seat switch, and operates each motor. If the position control ECU and switch assembly receives more than 2 motor operation signals, the motor is stopped. Manual operation is restarted after the position control ECU and switch assembly receives 1 signal only.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check that each function of the power seat operates normally by using the power seat switch.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| One or more power seat functions (except lumbar support adjustment function) do not operate | A |
| All power seat functions do not operate | B |
| Front vertical and lifter functions do not operate | C |
| Only lumbar support adjustment function does not operate | D |
A
B
C
D
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Driver Seat / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Reclining Rear | Reclining switch signal (Rearward) | ON or OFF | ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off |
- |
| Reclining Front | Reclining switch signal (Forward) | ON or OFF | ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off |
- |
| Front Vertical Down | Front vertical switch signal (Downward) | ON or OFF | ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off |
- |
| Front Vertical Up | Front vertical switch signal (Upward) | ON or OFF | ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off |
- |
| Lifter Switch Down | Lifter switch signal (Downward) | ON or OFF | ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off |
- |
| Lifter Switch Up | Lifter switch signal (Upward) | ON or OFF | ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off |
- |
| Slide Rear | Slide switch signal (Rearward) | ON or OFF | ON: Slide switch (Rearward) on
OFF: Slide switch (Rearward) off |
- |
| Slide Front | Slide switch signal (Forward) | ON or OFF | ON: Slide switch (Forward) on
OFF: Slide switch (Forward) off |
- |
| Tester Display |
|---|
| Reclining Rear |
| Reclining Front |
| Front Vertical Down |
| Front Vertical Up |
| Lifter Switch Down |
| Lifter Switch Up |
| Slide Rear |
| Slide Front |
ON or OFF is displayed on the intelligent tester according to the table above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Driver Seat / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Reclining | Seat reclining operation | OFF/Rear/Front | - |
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Lifter Operation | Seat lifter operation | OFF/Down/Up | - |
| Seat Slide Operation | Seat slide operation | OFF/Rear/Front | - |
| Tester Display |
|---|
| Seat Reclining |
| Tester Display |
|---|
| Front Vertical Operation |
| Tester Display |
|---|
| Lifter Operation |
| Tester Display |
|---|
| Seat Slide Operation |
| Result | Proceed to |
|---|---|
| The power seat functions operate normally. | A |
| Slide, front vertical or lifter function does not operate normally. | B |
| Reclining function does not operate normally. | C |
A
B
C
| *a | Component without harness connected
(Slide Motor (Separate Type Front Seat Cushion Spring Assembly)) |
Disconnect the d8, d9 or d10 connector from each motor.
Check the motor operation of applicable function.
Check the operation of the slide motor.
Check if the seat cushion moves smoothly when the battery is connected to the slide motor connector terminals.
| Measurement Condition | Operational Direction |
|---|---|
| Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1 |
Seat cushion spring moves forward |
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4 |
Seat cushion spring moves backward |
| *a | Component without harness connected
(Front Vertical Motor (Separate Type Front Seat Cushion Spring Assembly)) |
Check the operation of the front vertical motor.
Check if the seat cushion moves smoothly when the battery is connected to the front vertical motor connector terminals.
| Measurement Condition | Operational Direction |
|---|---|
| Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1 |
Seat cushion spring moves upward |
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4 |
Seat cushion spring moves downward |
| *a | Component without harness connected
(Lifter Motor (Separate Type Front Seat Cushion Spring Assembly)) |
Check the operation of the lifter motor.
Check if the seat cushion spring moves smoothly when the battery is connected to the lifter motor connector terminals.
| Measurement Condition | Operational Direction |
|---|---|
| Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1 |
Seat cushion spring moves upward |
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4 |
Seat cushion spring moves downward |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Reclining Motor (Separate Type Front Seatback Spring Assembly)) |
Disconnect f3 reclining motor connector.
Check the operation of the reclining motor.
Check if the seatback moves smoothly when the battery is connected to the reclining motor connector terminals.
| Measurement Condition | Operational Direction |
|---|---|
| Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1 |
Seatback moves forward |
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4 |
Seatback moves backward |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the d11 position control ECU and switch assembly connector.
Measure the resistance according to the value(s) in the table below.
Check the wire harness and connector between the position control ECU and switch assembly and applicable motor.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d11-3 (SLD+) - d8-4 | Always | Below 1 Ω |
| d11-4 (SLD-) - d8-1 | Always | Below 1 Ω |
| d11-5 (FRV-) - d9-1 | Always | Below 1 Ω |
| d11-8 (FRV+) - d9-4 | Always | Below 1 Ω |
| d11-10 (LFT+) - d10-4 | Always | Below 1 Ω |
| d11-12 (LFT-) - d10-1 | Always | Below 1 Ω |
| d11-9 (RCL+) - f3-4 | Always | Below 1 Ω |
| d11-11 (RCL-) - f3-1 | Always | Below 1 Ω |
| d11-3 (SLD+) - Body ground | Always | 10 kΩ or higher |
| d11-4 (SLD-) - Body ground | Always | 10 kΩ or higher |
| d11-5 (FRV-) - Body ground | Always | 10 kΩ or higher |
| d11-8 (FRV+) - Body ground | Always | 10 kΩ or higher |
| d11-10 (LFT+) - Body ground | Always | 10 kΩ or higher |
| d11-12 (LFT-) - Body ground | Always | 10 kΩ or higher |
| d11-9 (RCL+) - Body ground | Always | 10 kΩ or higher |
| d11-11 (RCL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the d12 position control ECU and switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d12-12 (SYSB) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the lumbar front power seat switch.
| *1 | Hold Switch |
| *2 | Release Switch |
| *a | Component without harness connected
(Lumbar Front Power Seat Switch) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 5 | Hold | Below 1 Ω |
| 2 - 3 | ||
| 2 - 3 | Off | |
| 2 - 1 | ||
| 3 - 5 | Release | |
| 1 - 2 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Lumbar Support Adjuster Assembly RH) |
Disconnect f2 lumbar support adjuster assembly RH connector.
Check the operation of the lumbar support adjuster assembly RH.
Check that the seatback moves smoothly when the battery is connected to the lumbar support adjuster assembly RH connector terminals.
| Measurement Condition | Operational Direction |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2 |
Seatback moves forward |
| Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 |
Seatback moves backward |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the d11 position control ECU and switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d11-6 (+B2) - d5-5 | Always | Below 1 Ω |
| d11-1 (GND2) - d5-2 | Always | Below 1 Ω |
| d5-1 - f2-1 | Always | Below 1 Ω |
| d5-3 - f2-2 | Always | Below 1 Ω |
| d5-5 - Body ground | Always | 10 kΩ or higher |
| d5-2 - Body ground | Always | 10 kΩ or higher |
| d5-3 - Body ground | Always | 10 kΩ or higher |
| d5-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG