Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.10–2015.04
RM19V0EQ _58 Vehicle Interior _014608 METER / GAUGE / DISPLAY _0074143 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge malfunction via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1500 Fuel Sender Open Detected When IG voltage is 9.5 V or more and the following condition is detected:
1.

Fuel sender gauge operation malfunction


·

Harness or connector

·

Fuel sender gauge assembly

·

Combination meter assembly



WIRING DIAGRAM

E156126E52
5.313,2.99 7.146,3.333 1.833,0.344 10 Combination Meter Assembly 6.063,0.896 6.469,1.208 0.406,0.313 10 FR 6.063,2.24 6.542,2.531 0.479,0.292 10 FE 5.802,0.885 6.188,1.167 0.385,0.281 10 18 5.802,2.24 6.135,2.458 0.333,0.219 10 17 2.104,2.24 2.667,2.646 0.563,0.406 10 3 2.125,0.885 2.458,1.167 0.333,0.281 10 2 0.344,3.042 2.385,3.552 2.042,0.51 10 Fuel Suction Tube Assembly with Pump and Gauge 0.51,1.542 1.135,2.427 0.625,0.885 10 Fuel Sender Gauge Assembly 1.292,1.427 1.656,1.771 0.365,0.344 10 2 1.292,2.094 1.604,2.333 0.313,0.24 10 1 1.802,2.24 2.292,2.573 0.49,0.333 10 FE 1.823,0.885 2.229,1.188 0.406,0.302 10 FS 5.323,2.844 5.771,3.146 0.448,0.302 10 I18 0.333,2.896 0.906,3.292 0.573,0.396 10 N11

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FUEL INPUT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Check the values by referring to the table below.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input signal Min.: 0 , Max. 127.5 Fuel receiver gauge indicates F: 62.9
Fuel receiver gauge indicates 3/4: 54.5
Fuel receiver gauge indicates 1/2: 35.0
Fuel receiver gauge indicates 1/4: 15.4
Fuel receiver gauge indicates E: 7.0
Unit: Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data can be displayed on the intelligent tester and DTC B1500 is output. A
Fuel level data cannot be displayed on the intelligent tester. B



A

REPLACE COMBINATION METER ASSEMBLY

B

2.INSPECT FUEL SENDER GAUGE ASSEMBLY
2.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
E224284C14
0.24,1.458 0.698,1.74 0.458,0.281 1.604,2.146 1.604,2.615 1.604,2.615 1.792,2.615 false 1.479,2.146 1.479,2.615 1.479,2.615 1.292,2.615 false 0.115,0.104 0.396,0.385 0.281,0.281 10 *a 1.833,2.531 2.365,2.771 0.531,0.24 10 FR 1.073,2.552 1.604,2.792 0.531,0.24 10 FE 0.375,1.51 0.792,2.146 0.417,0.635 10 I18
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the I18 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-18 (FR) - I18-17 (FE) Always 13.5 to 414.5 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
a.

Disconnect the N11 fuel suction tube assembly with pump and gauge connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-18 (FR) - N11-2 (FS) Always Below 1 Ω
I18-18 (FR) - Body ground Always 10 kΩ or higher
I18-17 (FE) - N11-3 (FE) Always Below 1 Ω
I18-17 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
E224291C04
2,4.083 2.75,4.083 false 1.583,2.75 2.75,2.75 false 2.833,3.99 2.99,4.188 0.156,0.198 10 E 2.844,2.667 3,2.865 0.156,0.198 10 F 0.229,0.188 0.542,0.385 0.313,0.198 10 *a
*a Front view of wire harness connector
(to Fuel Sender Gauge Assembly)


Remove the fuel sender gauge assembly.

See pageEngine / Hybrid System>2AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Check that the float moves smoothly between E and F.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Float level is F (upper) 13.5 to 16.5 Ω
1 - 2 Float level is between F (upper) and E (lower) 13.5 to 414.5 Ω (Gradually changes)
1 - 2 Float level is E (lower) 405.5 to 414.5 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
a.

Visually check for deformation on the fuel suction tube assembly with pump and gauge connector.

OK:

There is no deformation.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE