Home › Vehicle Interior › INTERIOR PANELS / TRIM › REAR SUNSHADE SYSTEM
RM19V0EQ _58 Vehicle Interior _014615 INTERIOR PANELS / TRIM _0074206 REAR SUNSHADE SYSTEM J

INTERIOR PANELS / TRIM  REAR SUNSHADE SYSTEM  Rear Sunshade Shift-linked Function does not Operate when Shift Lever is Moved to R Position  


DESCRIPTION

When the ignition switch is on IG and the shift lever is moved to R, the shift position sensors send a reverse (R) signal to the ECM. Then, the ECM sends this signal to the main body ECU (multiplex network body ECU) via CAN. When the rear sunshade relay (rear window shade assembly) receives this signal with the rear sunshade raised, the rear sunshade is lowered.

WIRING DIAGRAM

B235132E26
0.781,2.396 2.708,2.646 1.927,0.25 10 false : CAN Communication Line 1.333,1.854 1.948,2.146 0.615,0.292 10 false ECM 2.802,1.906 4.448,2.333 1.646,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 4.875,1.906 6.594,2.375 1.719,0.469 10 false Rear Sunshade Relay (Rear Window Shade Assembly) 2.802,1.74 3.177,1.979 0.375,0.24 10 false I13 4.875,1.75 5.365,2.063 0.49,0.313 10 false N19 5.271,0.938 5.594,1.083 0.323,0.146 10 false REV 3.75,0.938 4.26,1.198 0.51,0.26 10 false REV 3.146,0.938 3.615,1.24 0.469,0.302 10 false CAN 1.677,0.938 2.156,1.167 0.479,0.229 10 false CAN 5.073,0.833 5.292,1.052 0.219,0.219 10 false 3 4.135,0.833 4.552,1.073 0.417,0.24 10 false 15

CAUTION / NOTICE / HINT

NOTICE:

Since the rear sunshade system has functions that use CAN communication, first confirm that there is no malfunction in the CAN communication system using the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>INTERIOR PANELS / TRIM>REAR SUNSHADE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (R Range) PNP switch status ON or OFF ON: Shift lever in R
OFF: Shift lever not in R
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Powertrain > Engine and ECT > Data List
Tester Display
Shift SW Status (R Range)
50003 234 126
OK:

The intelligent tester display changes according to the shift state selected using the shift lever.



Result:
Proceed to
OK
NG



OK

2.CHECK ECM (REVERSE SIGNAL)

NG

2.CHECK ECM (REVERSE SIGNAL)
a.

Check if the shift position indicator in the combination meter assembly operates normally.

OK:

The shift position indicator indicates the actual shift position correctly.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

HINT:

Make sure the rear window shade assembly is raised before performing Active Test.


Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Reverse Gear Signal Reverse signal OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Reverse Gear Signal
50004 123 24

OK:

The rear window shade assembly is lowered.


Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

4.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)
4.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)
a.

Disconnect the N19 rear sunshade relay (rear window shade assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N19-3 (REV) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
5.CHECK HARNESS AND CONNECTOR (REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N19-3 (REV) - I13-15 (REV) Always Below 1 Ω
I13-15 (REV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR