Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM19V0EQ _59 Vehicle Exterior _014619 MIRROR (EXT) _0074232 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch  


SYSTEM DESCRIPTION

When the mirror adjust switch is operated, the main body ECU (multiplex network body ECU) detects the switch operation and sends the mirror adjust switch signal to the outer mirror control ECU assembly (front passenger door) via CAN communication. On receiving the signal, the outer mirror control ECU assembly (front passenger door) operates the vertical and horizontal mirror motors, which are built into the outer mirror actuator assembly (front passenger door), to adjust the mirror surface position.

WIRING DIAGRAM

B293969E62
0.146,4.26 1.365,4.677 1.219,0.417 10 false Outer Mirror Switch Assembly 0.146,4.083 0.677,4.354 0.531,0.271 10 false J12 1.844,4.052 2.177,4.313 0.333,0.26 10 false I12 1.844,4.229 3.469,4.677 1.625,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 0.896,0.875 1.438,1.167 0.542,0.292 10 false MSW 1.344,0.781 1.542,1.021 0.198,0.24 10 false 1 2,0.781 2.302,1.031 0.302,0.25 10 false 14 1.344,2.104 1.604,2.365 0.26,0.26 10 false 3 2.01,2.104 2.375,2.354 0.365,0.25 10 false 13 1.344,3.385 1.625,3.646 0.281,0.26 10 false 2 2.01,3.385 2.292,3.646 0.281,0.26 10 false 15 1.042,2.208 1.417,2.458 0.375,0.25 10 false M+ 1.146,3.5 1.396,3.719 0.25,0.219 10 false E 2.25,0.875 2.823,1.177 0.573,0.302 10 false MIRS 2.25,2.219 2.969,2.656 0.719,0.438 10 false MIRB 2.25,3.49 2.896,3.813 0.646,0.323 10 false MIRE 1,5.333 3,5.563 2,0.229 10 false : CAN Communication Line 2.76,1.625 3.24,1.896 0.479,0.271 10 false CAN 4.073,1.625 4.396,1.771 0.323,0.146 10 false CAN 4.729,0.875 5.281,1.167 0.552,0.292 10 false LMHR 4.729,2.219 5.292,2.542 0.563,0.323 10 false LM+R 4.729,3.5 5.24,3.719 0.51,0.219 10 false LMVR 5.219,0.771 5.438,1.083 0.219,0.313 10 false 9 5.219,2.115 5.448,2.365 0.229,0.25 10 false 10 5.219,3.396 5.427,3.625 0.208,0.229 10 false 1 3.74,4.24 5.5,4.823 1.76,0.583 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 3.74,4.063 4.083,4.375 0.344,0.313 10 false z6 5.625,4.156 7.052,4.802 1.427,0.646 10 false Outer Rear View Mirror Assembly (Front Passenger Door)

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

OK:

CAN communication DTC is not output.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH ASSEMBLY)

NG

GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Selection SW (L) Mirror select switch signal for LH mirror ON or OFF ON: Mirror select switch in L position
OFF: Mirror select switch off or in R position
-
Mirror Position SW (R) Mirror adjust switch signal (Right) ON or OFF ON: Mirror adjust switch pressed right
OFF: Mirror adjust switch not pressed right
Check with the mirror select switch in the L position
Mirror Position SW (L) Mirror adjust switch signal (Left) ON or OFF ON: Mirror adjust switch pressed left
OFF: Mirror adjust switch not pressed left
Check with the mirror select switch in the L position
Mirror Position SW (Up) Mirror adjust switch signal (Up) ON or OFF ON: Mirror adjust switch pressed up
OFF: Mirror adjust switch not pressed up
Check with the mirror select switch in the L position
Mirror Position SW (Dwn) Mirror adjust switch signal (Down) ON or OFF ON: Mirror adjust switch pressed down
OFF: Mirror adjust switch not pressed down
Check with the mirror select switch in the L position
Body Electrical > Main Body > Data List
Tester Display
Mirror Selection SW (L)
Mirror Position SW (R)
Mirror Position SW (L)
Mirror Position SW (Up)
Mirror Position SW (Dwn)
50003 123 99,100,101,102,103
OK:

On the intelligent tester screen, ON or OFF is displayed for each item according to the table above.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)

NG

5.INSPECT OUTER MIRROR SWITCH ASSEMBLY
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)
a.

Enter the following menus: Body / Mirror L / Active Test.


b.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Mirror L > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Mirror Up/Down Mirror vertical operation Up / Down
·

Operate with engine switch on (IG) and the vehicle stopped.

·

This test activates the mirror up or down.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Mirror Right/Left Mirror horizontal operation Right / Left
·

Operate with engine switch on (IG) and the vehicle stopped.

·

This test tilts the mirror right or left.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Body Electrical > Mirror L > Active Test
Tester Display
Mirror Up/Down
50004 225 2
Body Electrical > Mirror L > Active Test
Tester Display
Mirror Right/Left
50004 225 3
OK:

Power mirror operation is normal.



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)

NG

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
B294038C09
1.5,1.552 1.99,1.844 0.49,0.292 1.26,2.479 0.802,2.479 false 1.438,2.729 1.438,3.198 1.438,3.198 1.615,3.198 false 1.313,2.729 1.313,3.198 1.313,3.198 1.125,3.198 false 0.698,1.604 1.115,1.948 0.417,0.344 10 false *a 1.646,1.604 2.031,1.927 0.385,0.323 10 false z6 0.281,2.406 0.938,2.698 0.656,0.292 10 false LMVR 1.656,3.115 2.354,3.427 0.698,0.313 10 false LM+R 0.594,3.115 1.281,3.375 0.688,0.26 10 false LMHR
*a Component without harness connected
(Outer Mirror Actuator Assembly LH)


Remove the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL

i.

Apply battery voltage and check the operation of the outer rear view mirror assembly LH.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal z6-1 (LMVR)
Battery negative (-) → Terminal z6-10 (LM+R)
Turns upward
Battery negative (-) → Terminal z6-1 (LMVR)
Battery positive (+) → Terminal z6-10 (LM+R)
Turns downward
Battery positive (+) → Terminal z6-9 (LMHR)
Battery negative (-) → Terminal z6-10 (LM+R)
Turns left
Battery negative (-) → Terminal z6-9 (LMHR)
Battery positive (+) → Terminal z6-10 (LM+R)
Turns right




Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

5.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.
B294031C10
1.729,0.844 1.729,0.292 1.729,0.292 1.906,0.292 false 1.719,1.854 1.719,2.385 1.719,2.385 1.896,2.385 false 1.979,3.771 1.979,4.302 1.979,4.302 1.708,4.302 false 2.146,3.771 2.146,4.427 2.146,4.427 2.51,4.427 false 2.333,3.771 2.333,4.135 2.333,4.135 2.51,4.135 false 1.417,4.219 1.896,4.573 0.479,0.354 10 false M+ 1.938,2.313 2.271,2.615 0.333,0.302 10 false *1 1.938,0.198 2.24,0.5 0.302,0.302 10 false *2 2.563,4.333 2.906,4.604 0.344,0.271 10 false E 2.563,4.042 3.115,4.333 0.552,0.292 10 false MSW 0.479,2.823 0.854,3.146 0.375,0.323 10 false *a
*1 Mirror Adjust Switch
*2 Mirror Select Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Remove the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J12-3 (M+) - J12-2 (E) Mirror adjust switch pressed up 90 to 110 Ω
Mirror adjust switch pressed down 437 to 503 Ω
Mirror adjust switch pressed left 744 to 856 Ω
Mirror adjust switch pressed right 225 to 275 Ω
J12-1 (MSW) - J12-2 (E) Mirror select switch R Below 10 Ω
Mirror select switch L 90 to 110 Ω
Mirror select switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU)

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU)
a.

Disconnect the J12 connector from the outer mirror switch assembly.


b.

Disconnect the I12 connector from the main body ECU (multiplex network body ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J12-2 (E) - I12-15 (MIRE) Always Below 1 Ω
J12-3 (M+) - I12-13 (MIRB) Always Below 1 Ω
J12-1 (MSW) - I12-14 (MIRS) Always Below 1 Ω
J12-2 (E) - Body ground Always 10 kΩ or higher
J12-3 (M+) - Body ground Always 10 kΩ or higher
J12-2 (MSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR